GarrettCom Magnum 8000X Скачать руководство пользователя

Страница: 12 / 63

Magnum 8000X Mixed-Media Fiber Hubs Installation and User Guide (05/ 02)

www GarrettCom com

2.0

Introduction - Magnum 8000X Mixed-Media Fiber Hub

2.1

Inspecting the Package and Product

Examine the shipping container for obvious damage prior to installing this

product; notify the carrier of any damage which you believe occurred during shipment

or delivery. Inspect the contents of this package for any signs of damage and ensure that

the items listed below are included.

This package should contain:

1 - Magnum 8000X Base Unit (may have PMs factory configured)

1 - AC Power Cord (U.S. and other 115 vac only)

1 - Set of metal "Ears" for optional 19” rack mounting

1 - (Model 8000X-A only) Stacking Cable, 9” length

1 - Installation and User Guide

1 - Product Registration Card

Note: Port Modules (PMs) purchased with the 8000X unit are usually factory

configured and installed, and may be included as part of the 8000X unit
when it is received.

Port Modules purchased for field installation will be boxed in a “bar-of-
soap-size” cardboard carton with labeling to indicate the contents.

Remove the unit from the shipping container. Be sure to keep the shipping

container should the unit need to be shipped at a later date. To validate the product

warranty, please complete and return the enclosed Product Registration Card to

GarrettCom, Inc. as soon as possible.

In the event there are items missing or damaged contact the supplier. If the

unit needs to be returned please use the original shipping container. Refer to Chapter 5,

Troubleshooting, for specific product return procedures.

Содержание Magnum 8000X
































































Результаты поиска

Содержание Magnum 8000X

Отзывы:

Похожие инструкции для Magnum 8000X

Бренды по названию

Популярные бренды

GarrettCom Magnum 8000X, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Magnum 8000X

Отзывы:

Похожие инструкции для Magnum 8000X

Бренды по названию

Популярные бренды