Garner HD-2 Series, Руководство по эксплуатации

Страница: 2 / 6

2 of 6
HD-2 SERIES Operation Manual
Remove the plastic protective cases.
Although the data is completely degaussed in one operation,
a second pass rotated at 90 degrees is required to smooth
out any magnetic fluctuation.
Note: For DLT media that is to be re-used, a second pass
is needed. If the second pass is not completed, the tape
drive may eject the tape and indicate the tape needs
cleaning. A second pass at 90 degrees will correct this
condition. If you have any questions, please contact your
dealer.
First Pass
Second Pass
IMPORTANT SAFETY NOTES
No operator-serviceable parts inside
unit. Maintenance to be done only by
trained personnel.
Do not cover chassis ventilation slots
or block enclosure openings.
High Voltage exists inside unit even
when equipment is not under power.
All trouble shooting and wiring checks
must be performed by a qualified
electrician or authorized plant
personnel.
Check input voltage selection; if
not compatible with wall voltage,
have technician qualified by Garner
Products modify wiring inside this
system before connecting system
plug to wall voltage.
A non-shielded power cord may
be used to connect AC power to
the system. Use only power cords
approved by Garner Products
Unplug power cord from the wall to
disconnect power to the system.
For continued protection against risk
of fire, replace fuses with fuses of
same types and ratings only.
Disconnect main power and unplug
unit from the wall before installing
or removing device or servicing
equipment.
PACE MAKER USERS
Due to stray magnetic fields, consult your physician before operating.
LCD DISPLAY DEGAUSSING INSTRUCTIONS
The following information appears on
the LCD Display from power-up through
one automatic degaussing cycle:
Automatic Degaussing
Step 1: Press POWER button ON
GARNER
PRODUCTS, INC.
Displays Manufacturer.
HD-2
DATA ELIMINATOR
Displays Degausser Model.
FIRMWARE VER
##
Displays current firmware version.
TOTAL
# −− ##
Displays total erasing cycles. Number on left
indicates number of times the counter reached
50,000.
Insert Media
Session = 0
Ready for media to be placed in the Media
Drawer. Counter for erase cycles from power up.
Step 2: Insert media
Drawer Open
Lift drawer up and slide drawer out until it stops.
Display indicates media drawer is open.
Erase Cycle
Initiated
Closing the drawer automatically starts the
degauss cycle.
Charging
>>>>>>>>>>>>>>>>
Displays capacitor charging status.
--------------===|==
Visual indicator of erasing field strength.
Data Eliminated
Indicates power and erasing field strength was
verified good and data has been eliminated.
Step 3: Remove Media
Remove Media
Session = 0
Erase cycle has completed. Open drawer and
remove media.
Introduction
The degausser model Garner HD-2X and HD-2SS
are continuous duty capacitive discharge degaussers.
The unit is designed to erase hard drives and tape
cartridges that fit inside the drawer. The convenient
media loading design accommodates many different
types and sizes of media, without the need for
adapters.
Inspection
Inspect the degausser for shipping damage as soon as
it is unpacked. If the degausser or any accessories are
damaged or fail to operate correctly, notify carrier and
contact your dealer immediately
INITIATION
INSTALLATION
Power Plug
Plug the IEC connector attached to the supplied power
cord into the receptacle on the back of the unit.
Location
The degausser must be placed on a flat, hard
surface. Keep at least a 15 cm (6 inch) distance from
any object that may interfere with the coo ling fan
exhaust located on the backside of the degausser.
As a general rule, media not inten ding to be erased
should be kept about 60 cm (2 ft) away.
Cooling
Forced air-cooling is used to maintain safe ope rating
temperatures within the degausser. The air intake is
located on the back panel and the exhaust is through the
holes in the top panel. To ensure proper cooling, do not
block the air-intake and maintain at least a 15 cm (6 in.)
distance from the back of the degausser to any obstacle.
DEGAUSSING INSTRUCTIONS FOR DLT MEDIA
CONTROLS AND INDICATORS
POWER Button (RED): The power button switches the power on and off.
Media Drawer: The media drawer holds the media to be degaussed and activates and
deactivates the degaussing cycle when in the closed and open positions.
LCD display: The LCD display gives status, automatic count, total count, software version, field
strength, user instructions and fault messages.