manualshive.com logo in svg

Garmin GTX 327, Руководство по установке

Поделиться
Скачать
Garmin GTX 327 Скачать руководство пользователя страница 36

Page 5-6

GTX 327 Installation Manual

Revision K

190-00187-02

KEY (Key Lighting)

Selection

Description

MAN (Manual)

Key lighting is controlled manually by the pilot on the GTX 327
DISPLAY page.

AUTO (Automatic)

Key lighting is automatically controlled based on the parameters
entered on this configuration page.

LVL (Level)

Shows the current level of key lighting, based on the lighting input source (lighting bus voltage, or the
ambient light if the source is PHOTO) and the settings on this configuration page.  This field has a range
of 0 (zero) to 999.  The level is set by pressing the 8 and 9 keys when MAN mode is selected.  When in
AUTO mode, the field is for display only.

RSP TIME (Response Time)

Sets the speed with which the brightness responds to ambient light changes (only for AUTO key lighting
mode).  The higher the number, the slower the key lighting responds.  This field has a range of 3 to 7, and
is set to 4 at the factory.

MIN (Minimum)  (Auto Only)

Sets the minimum brightness of the key lighting.  The higher the number, the brighter the minimum
brightness.  Key lighting minimum brightness has a range of 0 (zero) to 99, and is set to 8 at the factory.
It is prudent to verify that key lighting characteristics match those of other equipment in the panel under
night lighting conditions.

KEY SRCE (Key Lighting Source)  (Auto Only)

Selection

Description

PHOTO (Photocell)

DEFAULT.  Key lighting level is determined by the ambient light
level as measured by the photocell on the GTX 327.

14V

Backlight level tracks a 14 Volt DC aircraft lighting bus.

28V

Backlight level tracks a 28 Volt DC aircraft lighting bus.

5V

Backlight level tracks a 5 Volt DC aircraft lighting bus.

SLOPE  (Auto Only)

Sets the sensitivity of the key lighting brightness to changes in the input level.  The higher the number,
the brighter the key lighting will be for a given increase in the input level.  This field has a range of 0
(zero) to 99, and is set to 50 at the factory.

OFFSET  (Auto Only)

Adjusts the key lighting level up or down for any given input level.  This field has a range of 0 (zero) to
99, and is set to 50 at the factory.  This may also be used to match lighting curves with other equipment in
the panel.

Содержание GTX 327


























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды