Device Information
Specifications
Edge 130 Plus Specifications
Battery type
Rechargeable, built-in lithium-ion battery
Battery life
Up to 12 hr.
Operating temperature range From -20º to 60ºC (from -4º to 140ºF)
Charging temperature range From 0º to 45ºC (from 32º to 113ºF)
Wireless frequency
2.4 GHz @ 5.6 dBm nominal
Water rating
IEC 60529 IPX7
1
Heart Rate Monitor Specifications
Battery type
User-replaceable CR2032, 3 V
Battery life
Up to 3.5 yr. at 1 hr./day
Water resistance
1 ATM
2
NOTE:
This product does not transmit heart
rate data while swimming.
Operating temperature
range
From -5° to 50°C (from 23° to 122°F)
Wireless frequency/
protocol
2.4 GHz @ 2 dBm nominal
Speed Sensor and Cadence Sensor Specifications
Battery type
User-replaceable CR2032, 3 V
Battery life
Approximately 12 mo. at 1 hr./day
Speed sensor storage
Up to 300 hr. of activity data
Operating temperature range
From -20º to 60ºC (from -4º to 140ºF)
Wireless frequency/protocol
2.4 GHz @ 4 dBm nominal
Water rating
IEC 60529 IPX7
1
Device Care
NOTICE
Do not store the device where prolonged exposure to extreme
temperatures can occur, because it can cause permanent
damage.
Avoid chemical cleaners, solvents, and insect repellents that can
damage plastic components and finishes.
Secure the weather cap tightly to prevent damage to the USB
port.
Avoid extreme shock and harsh treatment, because it can
degrade the life of the product.
Cleaning the Device
1
Wipe the device using a cloth dampened with a mild
detergent solution.
2
Wipe it dry.
After cleaning, allow the device to dry completely.
Caring for the Heart Rate Monitor
NOTICE
You must unsnap and remove the module before washing the
strap.
A build up of sweat and salt on the strap can decrease the ability
of the heart rate monitor to report accurate data.
• Go to
for detailed washing
instructions.
• Rinse the strap after every use.
1
The device withstands incidental exposure to water of up to 1 m for up to 30 min.
For more information, go to
2
The device withstands pressure equivalent to a depth of 10 m. For more
.
• Machine wash the strap after every seven uses.
• Do not put the strap in a dryer.
• When drying the strap, hang it up or lay it flat.
• To prolong the life of your heart rate monitor, unsnap the
module when not in use.
User Replaceable Batteries
WARNING
See the
Important Safety and Product Information
guide in the
product box for product warnings and other important
information.
Replacing the Heart Rate Monitor Battery
1
Use a small Phillips screwdriver to remove the four screws on
the back of the module.
2
Remove the cover and battery.
3
Wait 30 seconds.
4
Insert the new battery with the positive side facing up.
NOTE:
Do not damage or lose the O-ring gasket.
5
Replace the back cover and the four screws.
NOTE:
Do not overtighten.
After you replace the heart rate monitor battery, you may need
to pair it with the device again.
Replacing the Cadence Sensor Battery
The device uses one CR2032 battery. The LED flashes red to
indicate a low battery level after two revolutions.
1
Locate the circular battery cover on the back of the
sensor.
2
Twist the cover counter-clockwise until the marker points to
unlocked and the cover is loose enough to remove.
3
Remove the cover and the battery .
4
Wait 30 seconds.
5
Insert the new battery into the cover, observing polarity.
NOTE:
Do not damage or lose the O-ring gasket.
6
Twist the cover clockwise until the marker points to locked.
NOTE:
The LED flashes red and green for a few seconds
after battery replacement. When the LED flashes green and
Device Information
13
