background image

Connecting to Power Without Using an Ignition Switch

This method of connection is used most often on larger vessels and on vessels with multiple networked 
stereos and other marine devices. For these installations, a faster startup time is typically less critical, and it is 
more effective to use the breaker or a dedicated switch on the electrical panel to turn off the stereo and ensure 
that no unexpected power drain occurs.
Consult this diagram to plan the wire connections.

Item Description

Notes

Yellow wire

You should connect this wire to the red wire before you connect both 
wires to the manual switch or circuit breaker.

Red wire

You should connect this wire to the yellow wire so that it does not act as a 
physical standby switch.

1 A fuse (not included)

You must install this fuse on the red wire before you connect the red wire 
to the yellow wire.

Manual switch 
(optional)

This switch is needed only if a circuit breaker is not available or if it 
provides a more convenient method of cutting power to the stereo.

Black wire

Ground (-)

15 A fuse (not included)

This fuse is required if you are not able to connect to power through a 

15 A circuit breaker 

.

15 A circuit breaker

If a circuit breaker is not available, you must connect a 15 A fuse 

 on 

the yellow wire

Route all wires to the stereo wiring harness, the circuit breaker or switch, and the power source as 

necessary.
Do not connect the wiring harness to the stereo until after you have made all of the bare wire connections.

Install all of the necessary fuses on the red and yellow wires.
Connect the wiring harness to the stereo.
When the circuit breaker or manual switch is closed, the stereo is always on. You can use the power button on 
the stereo or a connected chartplotter or remote control to place the stereo in a low-power standby mode if 
needed.
NOTE: When you are not using the vessel, you should remove power to the stereo using the circuit breaker or 
manual switch to avoid draining the battery.

Apollo MS-WB670 Installation Instructions

7

Содержание 010-02346-00



















Отзывы: