Garland XE24 Скачать руководство пользователя страница 23

Страница: 23 / 32

Part # 4517125 (09/03)

Page 23

6. Use and to change the Instant on Time to

the desired value.

7. Press to save the changes.
8. Press to return to “PROGRAMMING MODE

MENU ITEMS”

9. Press again to exit.

To Change Control Type:

1. Press and hold for three, (3) seconds. “ENTER

CODE” will be displayed.

2. Using the Gap Setting buttons,

enter the code, (1251). “ENTER CODE **** ” will

be displayed.

3. Press

to enter the Programming Mode.

“PROGRAMMING MODE MENU ITEMS”

will be displayed.

4. Press

two, (2) times. “PROGRAMMING

MODE SYSTEM SETUP” will be displayed.

5. Press

eight, (8) times. “CONTROL TYPE

ELECTRIC (or GAS)” will be displayed. (type

varies by grill).

6. Use and to change Control Type to match

the design of the grill.

7. Press to save the changes.
8. Press to return to “PROGRAMMING MODE

MENU ITEMS”

9. Press again to exit.

To Turn Extended Time On/Oﬀ:

1. Press and hold for three, (3) seconds. “ENTER

CODE” will be displayed.

2. Using the Gap Setting buttons,

enter the code, (1251). “ENTER CODE **** ” will

be displayed.

3. Press

to enter the Programming Mode.

“PROGRAMMING MODE MENU ITEMS”

will be displayed.

PROGRAMMING continued

4. Press

two, (2) times. “PROGRAMMING

MODE SYSTEM SETUP” will be displayed.

5. Press

nine, (9) times. “EXTENDED TIME

NO (or YES)” will be displayed.

6.  Use   and   to turn Extended Time on or oﬀ.
7.  Press   to save the changes.
8.  Press   to return to “PROGRAMMING MODE

MENU ITEMS”

9. Press again to exit.

To Change the Grill Function:

1. Press and hold for three, (3) seconds. “ENTER

CODE” will be displayed.

2. Using the Gap Setting buttons,

enter the code, (1251). “ENTER CODE **** ” will

be displayed.

3. Press

to enter the Programming Mode.

“PROGRAMMING MODE MENU ITEMS”

will be displayed.

4. Press

two, (2) times. “PROGRAMMING

MODE SYSTEM SETUP” will be displayed.

5. Press

ten, (10) times. “FUNCTION

CLAMSHELL (or FLAT)” will be displayed.

6. Use

and

to toggle between Flat mode and

Clamshell mode.

7. Press to save the changes.
8. Press to return to “PROGRAMMING MODE

MENU ITEMS”

9. Press again to exit.

To Change the Start Delay:

1. Press and hold for three, (3) seconds. “ENTER

CODE” will be displayed.

2. Using the Gap Setting buttons,

enter the code, (1251). “ENTER CODE **** ” will

be displayed.

Содержание XE24

































Результаты поиска

Содержание XE24

Отзывы:

Бренды по названию

Популярные бренды

Garland XE24, Инструкции по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание XE24

Отзывы:

Бренды по названию

Популярные бренды