English
English
29/148
with soap and water as soon as possible, if you then
continue to feel irritated skin or eyes immediately
consult a doctor.
Do not refuel fuel in closed or poorly
ventilated places. Fumes from the fuel and
oil contain hazardous chemicals. In the case
of a concentration of gases produced by insufficient
ventilation, remove all that impedes the flow of clean
air from the area in order to improve ventilation. Do not
return to the area unless you have properly ventilated
the area and are certain that ventilation is sufficient so
this concentration does not happen again.
Petrol and oil are extremely flammable and
explosive under certain conditions. Do not
smoke and keep flames, sparks or heat
sources away from the machine.
Do not smoke while transporting fuel, when you fill out
the deposit or when you are working.
Do not refuel fuel in locations where there is the
presence of open flames, sparks or heat sources. Fill
the tank always in well-ventilated areas and with the
motor stopped. Do not overflow fuel when trying to
overfill the fuel tank. In the event of a fuel leak, be
sure to clean these leaks completely before starting,
move the machine away from the spillage area and
avoid any source of ignition until all vapors are gone.
Add fuel before starting the machine.
Never remove the cap of the fuel tank while the
engine is running or when the machine is hot.
Do not refuel in enclosed spaces, in poorly ventilated
areas or near flames.
Make sure the cap of the fuel is tightly and correctly
closed while you are using the machine.
Make sure to correctly and tightly close the cap on the
fuel after refilling.
Do not use fuel that it has been stored for longer than
2 months.
2.5. CARE AND USE OF THIS MACHINE
The chipper is only designed to shred pieces
of wood with a maximum diameter of 6cm. It is
prohibited to shred any other material (for example
metal, stones, plastics and any other material). If
you want to shred roots, remove the sand, mud or
other residues before shredding. Any other use of
the shredder not described here, annuls the warranty
responsibility of the manufacturer.
Check that all the safety devices are installed and in
good condition.
Remember that the machine operator is responsible
for the dangers and accidents caused to other people
or things. The manufacturer will not be in any way
liable for damages caused by improper or incorrect
use of this machine.
The cutting tool is very sharp. Not following the
instructions may cause severe damage.
Keep this machine maintained and in proper condition.
Check that the moving parts are not misaligned
or locked, that there are no broken parts or other
conditions that may affect the operation of this
machine. Whenever this machine is damaged, repair
it before use. Many accidents are caused by poorly
maintained machines.
Check:
- The machine completely and look for loose and
damaged parts (screws, nuts, etc.).
- Engine oil level.
- Damaged and/or defective welded parts.
Make sure that the machine has passed the adequate
maintenance controls. All damage caused by the use
Содержание 1190 QG
