background image

Section 9:  WARRANTY

IMPORTANT                                                   

Please Read Carefully Before Operating

This Welch® Vacuum Pump

UNPACKING

Inspect the pump carefully. If any damage has occurred, immediately file claim with the carrier immediately. Save the 

shipping container for carrier to inspect. 

OPERATING PUMP

Refer to the enclosed Instruction/Operation Manual for all information to properly operate and maintain the pump.

WARRANTY

This Welch Vacuum product is warranted to be free from defects in material and workmanship.  The liability of Gardner 

Denver Welch Vacuum Technology  under this warranty is limited to servicing, adjusting, repairing or replacing any unit 

or component part which in the judgment of Gardner Denver Welch Vacuum Technology  has not been misused, abused 

or altered in any way causing impaired performance or rendering it inoperative. No other warranties are expressed or 

implied.  The method of executing this warranty: servicing, adjusting, repairing or replacing shall be at the discretion of 

Gardner Denver Welch Vacuum Technology .  Vacuum pumps that have been used for any period, however short, will be 

repaired under this warranty rather than replaced.

The warranty is effective for one year from the date of original purchase when:

 

1. The warranty card has been completed and returned.

 

2. The product is returned to the factory or other designated service centers,      freight prepaid.

 

3. The product in our judgment is defective through no action or fault of the user.

If the product has become defective through misuse, abuse, or alteration, repairs will be billed regardless of the age of the 

product.  In this event, an estimate of the repair costs will be submitted and authorization of these charges will be required 

before the product is repaired and returned.

To reduce additional charges and delays either within or outside of the warranty period, contact Gardner Denver Welch 

Vacuum Technology  @410-712-4100 for a return authorization number.  Products without a return authorization number 

will be refused by our receiving department. Before shipping, properly pack the pump, insure it against loss or damage, 

and on the outside of the pump packaging and the packing slip write in the return authorization number.  Pumps damaged 

due to improper packaging are the customer’s responsibility.

27

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание Welch Self-Cleaning Dry Vacuum System DryFast 2025































Отзывы: