background image

Troubleshooting

 

 

P1700040 

 

29 

Troubleshooting 

 

Only manufacturing firm and authorized service workshops may work on the pump and their 
accessories during the warranty period. 

 

Trouble 

Cause 

Remedy 

by: 

with: 

Vacuum pump 
does not start 

No power supply 

Qualified 
electrician 

Check electrical installation 

Motor defective 

Service  
workshop 

Exchange 

Coupling defective 

Repair and/or exchange 

Starting temperature too low 

User 

Put vacuum pump in a warm 
place corresponding 
to the starting temperature 

Oil is resinous after too long storage 

User or 
Service  
workshop 

General maintenance / cleaning 

Vacuum pump 
does not 
generate a 
vacuum 

Ultimate pressure few mbar 
or atmospheric pressure, oil shortage 

User 

Top-up oil 

Oil is dirty 

Operate with gas ballast, or 
perform oil change with flushing 

Oil supply to pump unit interrupted 
or reduced 

User 

Check that the oil circulation 
is functioning, measure the oil 
pressure at operating 
temperature, 1 

– 1.2 bar 

overpressure, check that the 
pipes are clear and have no 
leaks 

Gas ballast valve open 

User 

Close the gas ballast valve 

Shaft seals defective 

User or 
Service  
workshop 

Exchange 

Work or pressure control valve  
defective 

Exchange 

Intake valve defective 

Repair 

Oil supply to pump aggregate reduced, 
Oil superimposition interrupted  
by work valve 

Repair 

Built-up pressure in the oil casing too 
high because of exhaust gas pipe 
or oil mist filter 

User or 
Service  
workshop 

Check exhaust pipe, change 
filter insert 

Vacuum pump 
runs very 
loudly 

Motor, rotary vanes and/or shaft seal 
rings defective,  
rotary vane spring broken 

Repair and/or exchange 

Vacuum pump 
runs hot 

Vacuum pump oil supply interrupted 

Check that the oil circulation 
is functioning, measure the oil 
pressure at operating 
temperature, 1 

– 1.2 bar 

overpressure, check that the 
pipes are clear and have no 
leaks 

Oil with too low a viscosity used 

Oil change 

Ambient temperature around vacuum 
pump too high 

User 

Change location 

Motor defective 

User or 
Service 
workshop 

Exchange 

Built-up pressure in the oil casing too 
high (

 0.5 bar) 

Check exhaust pipe, change 
filter insert 

Heavy loss of 
oil 

Through oil mist emission:  
work or pressure control valve 
defective 

Exchange  

Because of leak from oil casing: 
shaft seal defective, oil casing seals 
defective 

Repair and/or exchange 

Vacuum pump 
is not vacuum-
tight when 

Intake valve defective 

Repair and/or exchange 

Shaft seal ring on the drive side 
or oil pump defective 

Repair and/or exchange 

Содержание WELCH CRVpro Series

















































Отзывы: