background image

 

13-8-619    Page 32 

 

NOTICE 

A sudden drop of zero pressure differential or sudden heavy oil carryover may 
indicate a ruptured element. 

 

 

Inspection

 - After removal of separator element, shine a light inside the element to reveal areas of heavy 

dirt or varnish deposits or breaks (ruptures) in  element media. 
 

Removal of Oil Separator For Inspection or Replacement: 

 
 

DANGER 

Air/oil under pressure will cause severe personal injury or death.  Shut down 
compressor, relieve system of all pressure, disconnect, lockout and tagout 
power supply to the starter before removing valves, caps, plugs, fittings, bolts 
and filters. 

 

 

DANGER 

Compressor, air/oil reservoir, separation chamber and all piping and tubing 
may be at high temperature during and after operation. 

 

 
1. 

Be certain the unit is off and that no air pressure is in the oil reservoir. 

 
2. 

Disconnect, lockout and tagout the power supply to the starter. 

 
3. 

Remove the minimum pressure/check valve (air/oil separator housing) cover. 

 
4. 

Lift out the air/oil separator element. 

 
5. 

Inspect and/or replace the separator as necessary. 

 
6. 

Clean the sealing surfaces on the air/oil separator and the minimum pressure/check valve. 

 
7. 

Clean the orifice in the oil return line, the strainer in the oil return line and if necessary the air/oil 
separator housing. 

 
8. 

Grease the o-ring on the separator element and install the separator into the housing. 

 
9. 

Replace the o-ring between the minimum pressure/check valve and the air/oil separator housing. 

 
10.  Install the minimum pressure/check valve assembly and tighten the bolts alternately for even 

tightness. 

 
11.  Replace the sealing kit in the minimum pressure/check valve.  After the assembling of the valve, 

leave between a .05 to .08 inch gap between the nut and the cover of the valve.  See “Changing 
Minimum Pressure/Check Valve Seals,” page 19. 

 
12.  Run the unit and check for leaks. 

Содержание INTEGRA EFB99A






















































Отзывы: