background image

 

Cod. 710.0138.72.00 Rev.10 

– 02.2022 

© Copyright 2022 Gardner Denver - All rights reserved

                  

  9 

– 11

 

TROUBLE 

DISPLAY 

POSSIBLE CAUSE 

REMEDY 

WAT

ER IN T

HE SYSTEM

 

Control panel 

display is 

blank 

No power in the line. 

Restore the power in the line. 

GDD130-160F  

Phases connected incorrectly. 

Connect the phases correctly. 

Problems with cabling. 

Check cabling; if the trouble persists, replace it. 

Problems with the electronic control board. 

Check the electronic control board; if the trouble persists, 
replace it. 

 

The dryer is off. 

Turn it on by pressing the ON/OFF switch for 1 second. 

 

Dryer in stand-by. 

Wait 2 minutes after the dryer is switched on. 

Compressed air inlet/outlet inverted. 

Check if the compressed air inlet/outlet is connected 
properly. 

The flow rate and/or temperature of the air 
entering the dryer are higher than the 
nominal values. 

Restore the nominal conditions. 

The ambient temperature is higher than the 
nominal values. 

Restore the nominal conditions. 

The condenser is dirty. 

Clean the condenser. 

Condensate drain is not functioning. 
Pic.3 

Clean the condensate drainage system filter mesh. 

Replace the coil of the drainage solenoid valve if burned. 

Clean or replace the drainage solenoid valve if 
clogged/jammed. 
Check the C8 and C9 parameters of the electronic control 
board; if the trouble persists, replace it. 

Condensate drain is not functioning. 
Pic.4-5 

Check the no loss condensate drain; if the trouble persists, 
replace it. 

The temperature control probe is positioned 
improperly or faulty. 

Check the probe; if the trouble persists, replace it. 

GDD130-160F 

Intervention of the high pressure switch. 

Reset the high pressure switch. 

 

 

Problems with cabling or with the electronic 
control board. 

Check the cabling and the electronic control board, if the 
trouble persists, replace them. 

Activation of compressor’s internal thermal 
protection. 

Wait one hour and check again. If the fault persists: stop 
dryer and call your local Gardner Denver distributor. 

 

 

Problems with the electrical components of 
the compressor. 

Check the electrical components of the compressor. 

Defective compressor. 

Replace the compressor. 

The flow rate and/or temperature of the air 
entering the dryer are higher than the 
nominal values. 

Restore the nominal conditions. 

The ambient temperature is higher than the 
nominal values. 

Restore the nominal conditions. 

The condenser is dirty. 

Clean the condenser. 

The temperature control probe is positioned 
improperly or faulty. 

Check the probe; if the trouble persists, replace it. 

Fan pressure switch defective or burned out 
(if present). 

Turn off the dryer and call your local Gardner Denver 
distributor. 

High pressure switch defective or burned out 
(if present). 

Turn off the dryer and call your local Gardner Denver 
distributor. 

Gas leakage in the refrigerating circuit. 

Turn off the dryer and call your local Gardner Denver 
distributor. 

Defective fan. 

Replace the fan. 

Protection fuse burned out (if present). 

Replace the fuse. 

 

The temperature control probe is positioned 
improperly or faulty. 

Check the probe; if the trouble persists, replace it. 

Gas leakage in the refrigerating circuit 
without load. 

Turn off the dryer and call your local Gardner Denver 
distributor. 

 

The temperature control probe is positioned 
improperly or faulty. 

Check the probe; if the trouble persists, replace it. 

 

Series of alarms very close to each other. 

Call your local Gardner Denver distributor. 

 
 
 
 
 
 
 
 

Содержание GDD4F
















Отзывы: