![background image](http://html1.mh-extra.com/html/gardner-denver/electra-saver-eau-pd-200-hp/electra-saver-eau-pd-200-hp_operating-and-service-manual_3603248037.webp)
13–10–612 Page 27
5.
Following service, put the enable switch in the
down, ”+” position.
6.
Restore power to the unit. The display will read:
SHUTDOWN POWER FAILURE.
7.
Press the STOP/RESET. The display will show
the ready mode in the lower right hand corner.
8.
Press ENTER. The display will read:
ENTER TO SET UP AUTO TO SERVICE
9.
Press AUTO. The display will read:
OIL FILTER HOURS TILL CHANGE
10. Press ENTER. The display will read:
HOURS TILL NEXT OIL CHANGE
11. Press ENTER. If an advisory is present, it will be
displayed at this time.
12. Press ENTER to clear the advisory. The display
will read:
ENTER TO SETUP RESET TO EXIT
13. Push STOP/RESET to return to ready mode.
To prevent unauthorized programming, disconnect, tag
and lockout power supply and return the ENABLE
switch to the up, SET, position.
14. Restore power. The display will read:
SHUTDOWN POWER FAILURE
15. Press STOP/RESET to clear the advisory.
PROGRAMMING AND SETUP INSTRUCTIONS
FOR THE AUTO SENTRY–ES
CONTROLLER
Programming and setup is accomplished with the
”PROGRAM” keys. In all steps, the ”ENTER” key will
cause the controller to accept the displayed value into
memory and advance to the next programming func-
tion. The plus ”+” and minus ”–” keys will increase and
decrease displayed values, respectively. The right and
left arrow keys, ”
→
” and ”
←
”, position the cursor
(flashing digit). The number at the cursor will be the
number that is changed by the ”+” and ”–” keys. At
any point in the programming and setup routine, the
”STOP–RESET” key can be pressed to exit and return
to the ready mode.
In all steps of the programming routine, the top line of
the display will give a description of the parameter to be
programmed, while the bottom line shows the variable
that is capable of being altered by programming.
The following is a step by step guide to programing the
”AUTO SENTRY–ES” Controller.
Between each key it is necessary to
press the ”ENTER” key to restore the
new value and advance to the next
step.
1.
Press the ”ENTER” key to begin programming. If
the enable switch on the circuit board is in the set
position, the control proceeds to the setup adjust-
ments starting with step 2 below. If the slide
switch is down in the ”+” position, push ”ENTER”
to go from OIL FILTER CHANGE to OIL
CHANGE and then push ”ENTER” again to pro-
ceed to Step 2. Press ”AUTO” to display the hours
remaining until oil change or filter change is rec-
ommended. If service has been performed early,
press the ”AUTO” key to reset the timers to their
full number of hours. Press ”ENTER” to proceed
to the next display without affecting timers.
2.
In the top line, DISPLAY UNITS is indicated. The
bottom line will indicate ENGLISH (PSIG, Fahren-
heit) or METRIC (Bars, Celsius). Select the de-
sired mode and press ENTER to save and pro-
ceed.
3.
In the top line, NUM OF SEQ UNITS is displayed.
The bottom line will indicate a number in the range
of one through eight. This will be factory set at ”1”.
This should be set to a number corresponding to
the number of compressors that are currently
installed on this air system that also have AUTO
SENTRY–ES controllers. It should be noted that
all AUTO SENTRY–ES compressors on the sys-
tem must have the same number programmed
here to operate correctly in ”SEQUENCE” mode.
Setting the value in step 1 to one indi-
cates that no sequencing is to take
place. Consequently, steps 4, 5, and 6,
which relate to sequencing, are
skipped by the ”AUTO SENTRY–ES”;
Programming commences at step 7.
4.
In the top line, UNIT NUMBER is displayed. The
bottom line will again indicate a number of one
Содержание ELECTRA-SAVER EAU PD - 200 HP
