background image

 

     

 2

 

 

Wipe  their  hands  and  the  hammer 
handle  and  maintain  a  firm  grip  on  the 
handle  to  avoid  losing  control  of  the 
hammer while swinging and striking. 

 

 

Carefully  swing  the  hammer  to  avoid 
striking themselves, another person and 
objects  other  than  the  targeted  lugs  or 
hammer bar. 

 

 

Avoid  swinging  the  hammer  above 
shoulder height. 

 
VALVE SEAT PULLING 
 

 

DANGER 

 

The following precautions must be observed 
by  operators  and  maintenance  personnel  to 
avoid 

personal 

injury, 

death 

and/or 

equipment  damage  from  contact  with  the 
puller, hammer, wedge or broken parts from 
these  components  when  using  either  a 
hydraulic  or  wedge  valve  seat  puller.  
Operators 

or 

maintenance 

personnel 

should: 
 
Hydraulic Seat Puller 
 

 

Wear safety shoes and glasses. 

 

 

Chain or tie the jack down as it will jump 
violently 

when 

the 

valve 

seat 

disengages from the valve deck. 

 

 

Check to insure the pressure applied by 
the hydraulic pump does not exceed the 
hydraulic 

ram 

maximum 

pressure 

rating. 

 
Wedge Seat Puller 

 

 

Grind off any mushroomed material 
from the wedge before use.

 

 

 

Inspect the hammer and wedge to 
insure they are in good condition.  
Replace any of those parts, which are 
cracked, damaged or badly worn.

 

 

 

Wear safety shoes and goggles.

 

 

Check to insure they have safe footing.

 

 

 

Fully engage the wedge to prevent it 
from disengaging violently from the 
cover as a blow is struck.

 

 

 

Wipe their hands and the hammer 
handle and maintain a firm grip on the 
handle to avoid losing control of the 
hammer while swinging and striking.

 

 

 

Carefully swing the hammer to avoid 
striking themselves, another person and 
objects other than the targeted wedge.

 

 

 

Avoid swinging the hammer above 
shoulder height.

 

 
COVERS AND GUARDS 

 
 

 

DANGER 

 

Personal 

injury, 

death 

and 

/or 

equipment  damage  can  result  from 
contact with moving parts. All moving 
parts  must  be  equipped  with  covers 
and  guards.  All  covers  and  guards 
must  be  securely  positioned  at  all 
times when the unit is in operation. 

 
 
Covers and guards are intended to not only 
protect against personal injury or death, but 
to also protect the equipment from foreign 
object damage  
 
EQUIPMENT MOVING AND LIFTING 

 

 

DANGER 

 
Heavy  equipment  including  pumps,  pump 
packages  and  components  should  only  be 
moved  or  lifted  by  trained,  experienced 
operators,  who  are  physically  and  mentally 
prepared  to  devote  full  attention  and 
alertness 

to 

the 

moving 

and 

lifting 

operations.    An  operator  should  be  fully 
aware  of  the  use,  capability,  and  condition 
of both the equipment being moved and the 
equipment being used to move it. 

Содержание C2500Q QUINTUPLEX















































Отзывы: