background image

 

13-18-612    Page  2 

WARNING 

– PROHIBITION – MANDATORY LABEL INFORMATION 

 
 

Gardner Denver Rotary Screw compressors are the result of advanced engineering and skilled 
manufacturing.  To be assured of receiving maximum service from this machine, the owner must exercise 
care in its operation and maintenance.  This book is written to give the operator and maintenance 
department essential information for day-to-day operation, maintenance and adjustment.  Careful 
adherence to these instructions will result in economical operation and minimum downtime. 

 
 

Boxed text formats are used, within this manual, to alert users of the following 
conditions: 
 
Safety Labels are used, within this manual and affixed to the appropriate areas of 
the compressor package, to alert users of the following conditions: 

 
 
 

 

 

 

Indicates a hazard with a high level of risk, which if not avoided, WILL result in 
death or serious injury. 

 
 

 

 

Equipment starts automatically 

 

 

Cutting of Finger or Hand Hazard 

– Rotating 

impeller blade 

 

 

 

Cutting of Finger or Hand Hazard 

– Rotating fan 

blade 

 

 

Health Hazard 

– Explosive Release of Pressure 

 

 

High Voltage 

– Hazard of Shock, Burn, or Death 

Present until Electrical Power is Removed 

 

 

 

Entanglement of Fingers or Hand/Rotating Shaft

Содержание AirSmart VS80-110B

























































































Отзывы: