GardenCare GC3814 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 35

GardenCare GC3814 Скачать руководство пользователя страница 13

12

tightness.

5. While holding up the tip of the bar, adjust the

chain tension by turning the tensioner screw

until the tie straps just touch the bottom side of

the bar rail.

6. Tighten the nuts securely with the bar tip

held up (12 ~ 15 Nm). Then check the chain

for smooth rotation and proper tension while

moving it by hand. If necessary, readjust with

the chain cover loose.

7. Tighten the tensioner screw.

(1) Loosen
(2) Tighten
(3) Chain tension adjusting screw

It is very important to maintain the proper chain tension. Rapid wear of the guide

bar or the chain coming off easily can be caused by improper tension. Especially

when using a new chain, take good care of it since it should expand when first

used.

5.

Fuel and chain oil

■

Fuel

The engines are lubricated by oil specially

formulated for air-cooled 2-cycle gasoline

engine use. If oil is not available, use an

antioxidant added quality oil expressly labeled

for air-cooled 2-cycle engine use.

RECOMMENDED MIXING RATIO

GASOLINE 35 : OIL 1

These engines are certified to operate on

«
...
11
12
13
14
15
...
»

Содержание GC3814




































Отзывы:

Нет отзывов