13
GB
12
GB
6. Trouble-shooting
Warning ! Electric shock !
V
Disconnect the pump from the mains before
working on it.
1. Remove pump from the filter housing (see 5. Maintenance).
2. FP 750 E : Detach the cap
G
from the motor housing
F
at the
catches
H
.
Other pumps : Turn the pump housing
E
anticlockwise and
pull it vertically off the motor housing
F
.
3. Pull impeller unit
I
out of the motor housing
F
and clean.
4. Push cleaned impeller unit
I
back into the motor housing
F
.
5. FP 750 E : Push pump cap
G
onto motor housing
F
.
Other pumps: Press pump housing
E
vertically onto motor
housing
F
and turn clockwise.
FP 4000 E / FP 5000 E / FP 7500 E: During assembly, ensure
that the seal / foam filter
J
is correctly seated in the motor hous-
ing
F
.
Fault Possible
cause
Remedy
No water feature operating.
Mains plug not plugged in.
V
Plug in mains plug.
Impeller unit is blocked.
V
Clean pump.
Regulating valve at pump or
V
Open the appropriate
pond edge controller is closed.
regulating valve.
FP 1800 E / FP 2500 E /
Thermal overload switch has
1. Unplug the mains plug
FP 7500 E
been triggered
and allow the pump to cool
(pump has run dry).
2. Plug the mains plug back
in after approx. 2 minutes.
FP 750 E FP 1000 /
Electronic dry-running safety
V
Unplug the mains plug,
FP 1400 E / FP 4000 E /
has been triggered.
stand the pump in the
FP 5000 E / FP 7500 E
water and plug the
mains plug back in.
Water feature reduced in
Water feature insert is dirty.
v
Clean water feature
size and uneven
insert and nozzle pipe.
Air lock in the hose.
v
Fill connection hose for
pond edge filter/pump with
water.
(see 4. Initial Operation).
Filter housing / pond
v
Clean filter housing / -
edge filter dirty.
pond edge filter.
If any other faults arise, please contact GARDENA Service.
Clean filter housing :
Clean the filter of the pond
edge controller:
Clean water feature insert
and nozzle pipe :
Clean the pump :
Additional consumers (e.g. gargoyles) can be connected to the
side outlet
B
(1/2
”
, 3/4
”
and 1
”nipple)
The quantity of water can
be adjusted via the regulator
C
.
Note: The ball joint
D
can be used to align the water feature so
that it is vertical.
5. Maintenance
Warning ! Electric shock !
V
Disconnect the pump from the mains before working on it.
Do not use any hard objects or powerful detergents for cleaning
the set!
1. Unscrew nozzle pipe.
2. Unscrew water feature insert and remove from nozzle pipe.
3. Clean nozzle pipe and water feature insert in clean water.
1. Take water feature pump out of the water.
2. Unlock snap fastenings
6
and open up the filter housing
5
.
3. Clean filter housing
5
with a jet of water.
4. Hook the halves of the filter housing into each other and close.
Do not use any hard objects or powerful detergents for cleaning
the set!
Light soiling :
v
Clean the filter surface of the pond edge controller under
water.
Heavy soiling :
1. Disconnect the pond edge controller from the hose underwater
to prevent air from being drawn in.
2. Take pond edge controller out of the water, open and clean.
3. Reconnect the pond edge controller to the hose under water.
Side outlet :
B
C
D
7
5
6
E
G
I
J
H
F
