manualshive.com logo in svg

Gardasoft Vision PP420, Руководство пользователя, Страница: 3 / 26

Поделиться
Скачать
Gardasoft Vision PP420 Скачать руководство пользователя страница 3

 

3

 

Safety - English 

3.1.1

 

PP420 – Safety 

Please read this before using the PP420 family of products. If in doubt, contact your distributor 
or Gardasoft Vision. 

 Where this symbol appears in the manual, refer to the text for precautions to be taken. 

3.1.2

 

Heat 

The  PP420  can  get  very  hot.  It  should  be  positioned  where  personnel  cannot 
accidentally touch it and away from flammable materials. 

Read the section on Heat Dissipation. Do not exceed the power ratings given in the manual. Note 
that at the maximum ratings the case temperature can reach 80

o

C. 

3.1.3

 

Electrical 

The  user  must  ensure  that  the  potential  difference  between  any  combination  of  applied  signals 
does not exceed the supply voltage. WARNING: Higher voltages may cause a danger to personal 
health. 

The PP420 does not have complete tracking isolation of inputs and outputs. 

Transients caused by inductive loads must be suppressed external to the PP420. 

3.1.4

 

General

 

The PP420 must not be used in an application where its failure could cause a danger to personal 
health or damage to other equipment. 

If the equipment is used in a manner not specified by the manufacturer, the protection provided 
by the equipment may be impaired. 

Содержание PP420



























Отзывы:

Нет отзывов