background image

SAFETY NOTICE

WARNING POWER LINES CAN KILL YOU

DO NOT ERECT THIS ANTENNA NEAR ANY OVERHEAD WIRES,

UNDER ANY CIRCUMSTANCES.

Do to the unique nature of this antenna and it’s very small size, there should

be no reason to significantly elevate your Super “C” antenna.

1)  Do not erect this antenna near any overhead wires.  Assume all such wires to be power lines and

deadly.

 

2)  Do not transport this antenna from an assembly location to the installation site if you must travel

near or under overhead wires.

 

3)  Request advice from your local power company if power lines are anywhere near the proposed

location.

 
4)  If the antenna falls, DO NOT try and stop it.  Get out of the way.
 
5)  If any part of the antenna should ever come in contact with power lines. DO NOT TOUCH IT

OR ATTEMPT TO MOVE IT.  IMMEDIATELY CALL THE POWER COMPANY.

 
6)  In the event of an accident involving power wiring  DO NOT TOUCH THE VICTIM

DIRECTLY.  Send someone for help.

 
7)  Select a site which limits public access to the antenna.  During operation the antenna has a high

RF potential.  If  the possibility exists that people or animals could touch the antenna, place a

wooden fence around it.

 
8)  Choose a calm, dry day to erect the antenna.
 
9)  Always enlist the aid of at least one competent person to aid in the assembly and placement of

your antenna.

 
10)  Never use a ladder to help in the placement of your antenna.  A ladder is not needed and could

be dangerous.

 
11)  Do not connect the antenna until it is completely assembled and firmly and safely mounted.
 
12)  If you have any questions regarding the assembly or mounting of your antenna please call;
        (561) 571-9922.  We will be more than happy to assist you.

Содержание SUPER C


















Отзывы: