background image

3

When Installing the Unit

Do not expose the unit to rain or an environment
where it may be splashed by water or other liquids,
as doing so may result in fire or electric shock. 

Install the unit only in a location that can

structurally support the weight of the unit and the
mounting bracket. Doing otherwise may result in
the unit falling down and causing personal injury
and/or property damage.

Since the color camera is designed for in-door use,

do not install it outdoors. If installed outdoors, the
aging of parts causes the unit to fall off, resulting in
personal injury. Also, when it gets wet with rain,
there is a danger of electric shock. 

When the Unit is in Use 

Should the following irregularity be found during

use, immediately switch off the power, disconnect
the power supply plug from the AC outlet and
contact your nearest CBC dealer. Make no further
attempt to operate the unit in this condition as this
may cause fire or electric shock. 

If you detect smoke or a strange smell coming

from the unit.

If water or any metallic object gets into the unit. 

If the unit falls, or the unit case breaks.

If it is malfunctioning (no image appears).

To prevent a fire or electric shock, never open nor

remove the unit case as there are high voltage
components inside the unit. Refer all servicing to
your nearest CBC dealer.

Do not insert nor drop metallic objects or

flammable materials in the unit, as this may result
in fire or electric shock. 

Be sure to inspect the unit periodically for safety
use. Deterioration of the installed part may cause
dropping of the unit, resulting in personal injury
and/or property damage. Contact your CBC dealer
as to the periodical inspection.

When Installing the Unit

Avoid installing the unit in humid or dusty locations,

in locations exposed to the direct sunlight, near the
heaters, or in locations generating sooty smoke or
steam as doing otherwise may result in fire or
electric shock. 

Leave the installation of the unit to your CBC

dealer because the installation requires expert
experience and skills. If the unit falls, this could
cause personal injuries.

Do not hang things from the unit as this may cause

the unit to drop, resulting in personal injuries.

1. SAFETY PRECAUTIONS

Be sure to read the instructions in this section carefully before use.

Make sure to observe the instructions in this manual as the conventions of safety symbols and messages
regarded as very important precautions are included.

We also recommend you keep this instruction manual handy for future reference. 

Safety Symbol and Message Conventions 

Safety symbols and messages described below are used in this manual to prevent bodily injury and property
damage which could result from mishandling. Before operating your product, read this manual first and
understand the safety symbols and messages so you are thoroughly aware of the potential safety hazards.

WARNING

Indicates a potentially hazardous situation which, if mishandled,
could result in death or serious personal injury. 

Indicates a potentially hazardous situation which, if mishandled,
could result in moderate or minor personal injury, and/or property
damage.

WARNING

CAUTION

CAUTION

Содержание ZC-Y20PH





















Отзывы: