background image

 

 

 

 

 

Fixed Camera Quick Start Guide 

 

November 2014 

Document Number 1012610

 

Version D 

 

 

©Copyright 2013, CBC AMERICA, Corp. - All rights reserved. The contents of this document may not be reproduced in whole or in part without the written 

consent of the copyright owner.

 

Important Safety Instructions

 

1.

 

Read these instructions. 

2.

 

Keep these instructions. 

3.

 

Heed all warnings. 

4.

 

Follow all instructions. 

5.

 

Install in accordance with the manufacturer’s instructions. 

6.

 

Do not defeat the purpose of the polarized or grounding-type plug.  
A polarized plug has two blades with one wider than the other. A 
grounding type plug has two blades and a third grounding prong.  
The wide blade or the third prong is provided for your safety.  If the 
provided plug does not fit into your outlet, consult an electrician for 
replacement of the obsolete outlet.  

7.

 

Use only with the tripod or bracket specified by the manufacturer, or 
sold with the apparatus.   

8.

 

Installation of the equipment must comply with local and national 
electrical codes. 

9.

 

This product must be connected to a Power Over Ethernet IEEE 
802.af compliant power source or a UL Listed “Class 2” power supply 
rated 12-24 V DC or 24 V AC minimum 13 W or 0.54 A. 

10.

 

Operating the camera at voltage levels outside the specified range 
may result in permanent damage to the unit and void the product 
warranty. 

11.

 

Clean the camera lens only with Kodak lens cleaning paper.   

12.

 

Failure to follow the proper procedure may cause permanent 
damage to the camera and void the product warranty. 
 

 
 
 
 

 

 

WARNING 

DEVICE SENSITIVE TO ELECTROSTATIC DISCHARGE 

The  camera  electronics  and  electronic  interfaces  are  sensitive  to 

electrostatic  discharge.  Please  follow  appropriate  ESD  procedures  when 

handling  the  camera  and  during  installation.    For  PoE  installations,  Ganz 

strongly  recommends  the  use  of  STP  cabling  and  an earth  grounded end 

point to ensure proper ESD immunity.  For AC or DC powered installations, 

a properly earth grounded power source is strongly recommended.

 

 

 

 

CAUTION 

To ensure a proper earth ground (between the Ganz Thermal camera and a 

PoE  switch)  Ganz  strongly  recommends  the  use  of  Shielded  Twisted  Pair 

(STP) cabling.  Installations of Ganz Thermal cameras using a STP cabling 

and a properly earth grounded PoE switch are tested to comply with industry 

immunity  standards  for  Electro  Static  Discharge.    Any  other  installation 

method may leave the camera at risk and void the warranty. 

 

 

 

Содержание ZNT6-H












Отзывы: