Gantner GAT NET.Lock 7020 System Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 64

background image

GAT NET.Lock 7020 System

Electrical Connections

46

HB_GAT-NETLOCK7020--EN_12

www.gantner.com

4.5

GAT NET.Controller M 7020

4.5.1 Ethernet Connection

The  connection  of  several  GAT  NET.Controller  M  7020  as  well  as  the  connection  of  the  master  controller  to  a
PC/server is performed via Ethernet.
►  Connect the Ethernet cable to the RJ45 plug labelled “Ethernet” on the side of the GAT NET.Controller M 7020.

Figure 4.12 - GAT NET.Controller M 7020 Ethernet connection

4.5.2 Power Supply Connection

The GAT NET.Controller M 7020 connects to the mains power supply via an external power supply. The GAT
NET.Power Supply 7020 100-240V / VI (Part No. 1100051) must be used to power the GAT NET.Controller M 7020.
Depending on the country, mains voltage may be U

AC

230 V or U

AC

115 V (refer to "7 TECHNICAL DATA

► Connect the power supply to the MOLEX plug labelled “Power” on the controller.

Figure 4.13 - Power supply connection on the GAT NET.Controller M 7020

«
...
44
45
46
47
48
...
»

Содержание GAT NET.Lock 7020 System

































































Отзывы:

Нет отзывов

Похожие инструкции для GAT NET.Lock 7020 System

Yale Smart Latch

Бренд: Assa Abloy Страницы: 2

Бренд: Satel Страницы: 4

Бренд: MARKS USA Страницы: 4

Comptronic 6124

Бренд: S&G Страницы: 2

SmartKey Series

Бренд: Kwikset Страницы: 3

Бренд: Hama Страницы: 22

Бренд: Phoenix Страницы: 2

Бренд: Phoenix Страницы: 2

Бренд: Alarm Lock Страницы: 6

Бренд: Weiser Страницы: 11

Siedle Steel SCOM 611-02

Бренд: SSS Siedle Страницы: 24

Бренд: TriTeq Страницы: 3

Timberline CB-235

Бренд: COMPX Страницы: 1

Бренд: Robern Страницы: 2

Resettable 160 Series

Бренд: Abus Страницы: 2

Бренд: IEI Technology Страницы: 6

Бренд: Dormakaba Страницы: 12

Austral Lock Virtus Two Point Hinged Door Mortice...

Бренд: Gainsborough Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды