Gantner GAT NET.Lock 7020 System Скачать руководство пользователя страница 59

Страница: 59 / 64

GAT NET.Lock 7020 System
Technical Data

www.gantner.com

HB_GAT-NETLOCK7020--EN_12

TECHNICAL DATA

7.1

GAT NET.Lock 7020

Nominal voltage

- GAT NET.Lock 7020 (P):

DC 5 V

- GAT NET.Lock 7020 USB (P):

DC 24 V

Power supply:

Via connection cable from sub controller

Average power consumption

- GAT NET.Lock 7020 (P):

60 mW

- GAT NET.Lock 7020 USB (P):

65 mW (without USB charging, without LED)

Charging current

(GAT NET.Lock 7020 USB (P))

Up to 2 A per lock and max. 70 W per controller*

* When multiple devices are being charged simultaneously at multiple locks of a sub

controller, the charging current of the sub controller is automatically distributed

between these locks.

Max. transmission power:

<400 mW

RFID frequency

- GAT NET.Lock 7020 (USB):

13.56 MHz

- GAT NET.Lock 7020 (USB) P:

13.56 MHz + 125 kHz

Break-in resistance capability:

DIN 4547-2 class C

Signaling element:

Multi-color status LED

Interface to sub controller:

One-wire (special cable for supply, data, and RF signal)

Connectors:

MOLEX, type Micro-

Fit 3.0™

Housing material:

Plastic (PC)

Door width:

Min. 230 mm (9.05 in)

Dimensions

- GAT NET.Lock 7020 (P):

110 x 100 x 25 mm (4.33 x 3.94 x 0.98 in)

- GAT NET.Lock 7020 USB (P):

110 x 100 x 37 mm (4.33 x 3.94 x 1.46 in)

Weight:

Approx. 160 g (5.6 oz)

Permitted ambient temperature:

0 °C to +60 °C (32 °F to 140 °F)

Protection type:

IP 52

Protection class:

III

Environment class based on VdS 2110:

II (conditions in indoor areas)

Compliance:

CE, FCC, IC, ETL

Содержание GAT NET.Lock 7020 System

































































Результаты поиска

Содержание GAT NET.Lock 7020 System

Отзывы:

Похожие инструкции для GAT NET.Lock 7020 System

Бренды по названию

Популярные бренды

Gantner GAT NET.Lock 7020 System, Установка, настройка и эксплуатация

Результаты поиска

Содержание GAT NET.Lock 7020 System

Отзывы:

Похожие инструкции для GAT NET.Lock 7020 System

Бренды по названию

Популярные бренды