background image

Startup and Configuration

Power supply

The GAT Lock 6010 F is powered by a 6 V battery (see technical data). 
Use the battery key to open the battery compartment of the GAT Lock 
6010 F as shown below.

         Right-hinged door 

 

           Left-hinged door

Inserting the battery:
1.  Ensure the battery polarity is correct.
2.  Press the battery down into the compartment until it locks into place.
3.  Swing the battery cover back over the battery compartment.

NOTE! 

Insert the battery directly before the GAT Lock 6010 F is 

mounted to avoid unnecessary battery usage. Only use the approved 
battery listed in the “Accessories” section on page 1 (1 x Batterie 6V 
Lithium 2CR5, Part No.: 125273).

Configuration

The GAT Lock 6010 F can be configured via PC/laptop and configuration 
software or by using the system data carriers included in the GAT Lock 
Basic Set 6000 F. A detailed description of the configuration process is 
available in the user manual.
For PC/laptop configuration, connect the programming cable to the jack 
in the battery compartment of the GAT Lock 6010 F as shown below.  
Connect the other end of the programming cable to a spare USB port on 
the PC/laptop. 

Communication is activated using the service data carrier. The programming 
cable and service data carrier are included in the GAT Lock Basic Set 
6000 F.

4

www.gantner.com

Valid from February 27

th

, 2017 • Technical data subject to modification without notice.

DB_GAT-LOCK6010F--EN_21.indd • Part No.: 985287

Battery key

Battery contacts

Battery compartment contacts

1

2

PC/laptop with 

configuration software 

Programming cable

Jack

Battery compartment

Battery

USB connector (type A)

  
  Safety Instructions

-  The installation and maintenance of this device must be 

performed by trained, qualified personnel.

-  All applicable safety and accident prevention regulations 

must be observed.

-  Safety devices must not be removed.
-  Please observe the technical data of the device specified in 

this datasheet.

-  The device must be disconnected from the power supply 

prior to installation, assembly or dismantling. 

Содержание GAT Lock 6010 F

Страница 1: ...tags The GAT Lock 6010 F is suitable for different types of locker material wood HPL solid plastic glass steel sheet and can be used with both left and right hinged doors The various operating modes provide flexibility allowing the locker system to be configured to suit individual requirements Description Part No GAT Lock 6010 F Battery lock for MIFARE data carriers dark gray housing light gray bu...

Страница 2: ...free Housing colour Dark gray Dimensions 112 x 110 x 33 mm Weight 0 2 kg Permitted ambient temperature 0 C to 60 C Protection type IP 52 Protection class III Environment class based on VdS 2110 II conditions in indoor areas Compliance CE FCC IC EAC 2 www gantner com Technical data Typical application Dimensions Right hinged door Left hinged door 1 Lock electronics 2 Battery compartment 3 Button 4 ...

Страница 3: ...pends on the type of data carrier used For metallic locker doors different values apply for the button drill hole and reading range refer to the GAT Lock 6010 F manual Mounting Right hinged door Left hinged door Use the correct screws according to the type of locker material max Ø 4 mm 0 16 The maximum allowed tightening torque of the screws is 2 Nm 1 47 lb ft Ensure that the button is centrally a...

Страница 4: ...r manual For PC laptop configuration connect the programming cable to the jack in the battery compartment of the GAT Lock 6010 F as shown below Connect the other end of the programming cable to a spare USB port on the PC laptop Communication is activated using the service data carrier The programming cable and service data carrier are included in the GAT Lock Basic Set 6000 F 4 www gantner com Val...

Отзывы: