background image

8

 ~ 

 

Optional Extra Equipment: (Ordered Separately) 

 

Calibration Pans: 

Calibration pan hangs under the spreader to catch 
material for weighing to check application rates.

 

Jigglers Packages: 

Use with materials that bridge.  
When installed, Jigglers contact the rotor bar and 
move up and down to help maintain an even flow. 

Part Number for 24” Spreader: 28248584 
Part Number for 36” Spreader: 28368584 

Part Number for 24” Spreader: J24 
Part Number for 36” Spreader: J36 

 

 

28248584 

J36 

 
 
 
 

 

 

Limited Warranty 

The Gandy Company warrants all material and workmanship on Gandy

 

equipment delivered to be free 

of defects for a period of 12 months from date of original purchase. Products used on a commercial, rental or 
leased basis are warranted for 90 days. Any part or parts thought to be defective within these warranty periods 
are to be returned through your servicing dealer or distributor to the Gandy Company's plant. Distributor or 
dealer must receive authorization from Gandy Company to return items under warranty. An authorization 
number will be issued and must be clearly visible on all packages returned to the factory. If found defective by 
Gandy Company, replacement parts will be forwarded free of charge,  prepaid.  No  service,  labor  charge  or 
expense  on  the  equipment  will  be  allowed  unless  such  expense  has  been previously authorized in writing by 
the Gandy Company. Serial number and model of the unit involved is required by the Gandy Company on all 
warranty claims. Gandy Company policy is to improve products whenever it is practical to do so. It reserves the 
right to make changes or add improvements at any time without incurring any obligation to make such changes 
on products sold previously.  This warranty does not apply to products altered or misused by users after the point 
of manufacture. 

This warranty against defects in material and workmanship is in lieu of all other warranties, expressed or 

implied, and  there  are  no  other  warranties  of  any  kind  whatsoever  including,  but  not  limited  to,  any  
implied  warranty  of merchantability  or  fitness  for  any  particular  purpose.  In  no  event  shall  the  company 
be  liable  for  any  incidental  or consequential damages whether for breach of warranty, for breach or 
repudiation of any other term or condition hereof, or for negligence, on the basis of strict liability, or for any 
other reason.

 

 
 

Gandy Company 
815 Rice Lake Street 
Owatonna, MN 55060 
Website: 

www.gandy.net

 

 

Form 2436OM808-IP 

 

Phone: 507-451-5430 

800-443-2476 

Fax: 507-451-2857 

Email: 

[email protected]

 

Printed in the USA 

 

Содержание 36H12











Отзывы: