background image

If you choose to vary from these instructions your warranty will be impaired

6

GALVO TIP

To hinge the door of your shed on 

the opposite side, simply put the 

top channel on the bottom and 

the bottom channel on the top.
Put the padbolt on the door 

before erecting the panels. 
It will stop your garage door 

swinging around!

3

CHANNELS 

The higher side of the channel goes 

to the inside of the shed. It is very 

important to include the fixings on the 

underside of all the channels as they 

are structural (except roof channels).

OUTSIDE

INSIDE

F

CHANNELS WITH 

CUTOUTS

The cutouts go to the inside 

of the panel to allow easy 

fitment of the end walls on 

assembly (page 5).

TOP

BOTTOM

IMPORTANT ADDITIONAL INFORMATION

STEP 7 

FRONT WALL

Lay down the doors with the sheets attached. Cap the sheets with the 3000mm 
channels 

F

. Use the door spacers 

K

 to make sure the door fits the gap (they sit 

on top of the 'Z' door jambs 

N

 see diagram 1).

Drill and fix (rivet or screw) the channels at every second rib down through the top.
Attach the door spacers at each end through the 'Z' door jambs and channels.
Put three fixings underneath through the channels into the sheeting pan and the 
top and bottom of the door spacers and 'Z' door jambs (see diagram 1).
Fit the padbolt 

P

 to the door strap on the outside of the door 

and the other two 

padbolts at the top and bottom of the other door sides and the keepers on 
the 'I channels.

Channels will come short  

of the ends of the sheeting by  

10-15mm on all panels.

P

F

F

K

K

YOU WILL NEED

2 x 3000mm 'U' channels with ends cut

2 x 1586mm door spacers

3 x padbolts

F

K

P

Fix through the top and bottom of the channels into the door 

jamb and spacer. The door jamb goes on inside of the channel.

SPACER

CHANNEL

PADLOCK KEEPER 

ASSEMBLY

KEEPER
RIVET

DOOR

Содержание GVO 3023









Отзывы: