Galvamet i-HOOD, Инструкция по установке, эксплуатации и обслуживанию

Страница: 7 / 8

MUSIC
key: Bluetooth. Press three seconds to activate the Bluetooth (the
button starts flashing). Enable the Bluetooth on the external device and
research the hood (initials RN52- .......). Once connected the button
light stops blinking and stays on, the display will show BT. Use the
external device to manage music and phone calls.
Use the key (volume) to adjust the volume, the display will show
the volume level
To accept or end a call press the key. During a phone call, the display
will sh
ow “CALL”. During a phone call you can adjust the volume using
the key
To disconnect the external device, hold for three seconds the key,
the device will be disconnected and the backlight intensity of the button
will reduce in stand-by mode.
key: Radio. Press three seconds to activate the radio. The backlight
button lights up, the display will show the radio station frequency. To
change frequency press the keys
Use the key to adjust the volume, the display will show the volume
level
To turn off the radio press the radio key for three seconds, the radio
turns off and the backlight intensity of the button will reduce in stand-by
mode.
The radio does not work when the hood is already connected with
Bluetooth and is receiving music from the external device or when there
is an active phone call.
Phone calls and the transmission of music tracks has priority over the
radio.
In any case, after 10 seconds of unused, the display will show the
volume level.
Filters maintenance reminder
Aluminium anti-grease filters
Once the hood is switched off, after 30 hour functioning, all the LEDs of
the speed buttons switch on with a fixed light for 30 seconds to remind
that aluminium anti-grease filter need cleaning.
To reset the timer keep pressed the buttons with the aspirator
switched off, otherwise the reminder will occur again when the hood is
switched off.
Charcoal filter (for filtering hoods)
Once the hood is switched off, after 120 hour functioning, all LEDs blink
for 30 seconds to remind that the charcoal filters (if present) need to be
replaced.
To reset the timer keep pressed the buttons with the aspirator
switched off, otherwise the reminder will occur again when the hood is
switched off.
MAINTENANCE
Always disconnect the hood from the mains before carrying out any
maintenance or cleaning operation.
Particular attention should be paid to the metallic anti-grease filters that
are designed to trap particles of fat contained in the fumes. The metallic
anti-grease filters must be washed at least once a month with detergent
in hot water (or in the dish-washer).
The filters may discolour after a few
washes. This is normal and does not mean they have to be replaced.
ATTENTION: the grease collected in the filters can easily catch fire and
it is therefore extremely important to clean the metallic filters on a
regular basis as per instructions.
The activated charcoal filters are designed to collect unpleasant odours
in the cooking fumes. The air is then released purified in the
environment. The charcoal filters must not be washed, but replaced 2 or
3 times a year, depending on how much the hood is used. New filters
are to be requested directly to the manufacturer. In order to replace the
activated charcoal filters, you should remove the anti-grease filters.
Your are then to take off the activated charcoal filters placed at the two
ends of the aspirator. Turn the filters until they unfasten from aspirator
(Picture 3 - D) .
Invert the operation in order to install the new charcoal filters.
In order to remove the remaining glue or any impurity, the cooker hood
must be cleaned immediately after installation and after having
removed the protective film.
The cooker hood must be cleaned frequently both internally and
externally (at least once a month).
Do not let dirt gather on the inner and outer surfaces of the hood.
To clean the exterior of the hood do not use either acid or basic
products, or abrasive sponges.
Clean the hood with a sponge dampen in warm water and a little
quantity of neutral detergent (for example dishwasher detergent), in
order to remove possible particles of grease.
Rinse with a damp cloth, removing all the detergent carefully, following
the satin finish direction on the steel surface.
Drying is very important, especially in areas where water is particularly
hard and leaves limestone.
The hood features a LED light that, in addition to offering a good
lighting and a significant energy savings, are guaranteed to last on
average 10 times more than traditional lights. For replacement, contact
the Assistance Service.