-
-
-22-
-22-
9. – CORRECTION OF POSSIBLE FAULTS
9. – CORRECTION OF POSSIBLE FAULTS
FAIL
FAIL
URE
URE
POSIBLE
POSIBLE
CAUSE
CAUSE
CORRECTION
CORRECTION
Empty
Empty air
air receiver
receiver (s)
(s)
Charge
Charge receiver
receiver (s)
(s)
Flow
Flow valve
valve (s)
(s) closed.
closed.
Open
Open flow
flow valve
valve (s)
(s)
Control
Control circuit
circuit blocked.
blocked.
Disconnect
Disconnect and
and clean
clean out
out
There
There is
is not
not signal
signal for th
for the
e electro
electro
valve
valve
Control
Control signal
signal
1
1
On pressing push-
On pressing push-
button, starter does not
button, starter does not
respond and not air flow
respond and not air flow
seems to exist in control
seems to exist in control
circuit.
circuit.
Leak
Leak in
in control
control duct.
duct. ..
Repair
Repair or
or replace.
replace.
Insufficient
Insufficient air
air pressure
pressure
Increase
Increase pressure
pressure in
in receiver
receiver
Piston
Piston 7
7 and
and valve
valve 8
8 sticking
sticking in
in
closed position
closed position
Remove
Remove and
and check
check both,
both, smoothen
smoothen
guides or change parts.
guides or change parts.
2
2
On pressing push-
On pressing push-
button, starter does not
button, starter does not
respond, although air
respond, although air
flows through control
flows through control
circuit
circuit
Electro
Electro valve
valve or
or filter
filter choked.
choked.
Excessive
Excessive length
length of
of main
main air
air
pipework
pipework
Remove
Remove and
and clean
clean the
the same
same
Approach
Approach push-button
push-button to
to starter
starter or
or
install a solenoid valve near the starter
install a solenoid valve near the starter
Ring
Ring gear
gear and/or
and/or pinion
pinion have
have burrs
burrs
or are damaged
or are damaged
Clean
Clean burrs
burrs or
or replace
replace if
if necessary.
necessary.
Replace pinion by a more adequate
Replace pinion by a more adequate
one.
one.
3
3
Pinion revolves and
Pinion revolves and
advances, but does not
advances, but does not
engage the ring gear.
engage the ring gear.
Lack
Lack of
of clearance
clearance between
between pinion
pinion
and ring gear
and ring gear
Check
Check by
by distortion
distortion of
of ring
ring gear.
gear.
Push-rod
Push-rod 11
11 inoperative
inoperative
Disassemble,
Disassemble, check,
check, smoothen
smoothen
guide diameter, clean or replace if
guide diameter, clean or replace if
rusted
rusted
Insufficient
Insufficient air
air pressure
pressure
Increase
Increase pressure
pressure in
in receiver.
receiver.
Splined
Splined shaft
shaft 19
19 sticking
sticking
Disassembl
Disassemble
e and
and clean,
clean, check
check
spring 22 and reassemble.
spring 22 and reassemble.
4
4
Pinion revolves but does
Pinion revolves but does
not advance
not advance
Pneumatic
Pneumatic motor
motor inoperative
inoperative
Disassemble,
Disassemble, inspect
inspect rotors
rotors for
for
foreign matters between teeth and for
foreign matters between teeth and for
possible wear of gears, spindles and
possible wear of gears, spindles and
bearing.
bearing.
5
5
Pinion advances but
Pinion advances but
does not rotate.
does not rotate.
Check
Check valve
valve 13
13 stuck
stuck of
of blocked.
blocked.
Disassemble,
Disassemble, clean,
clean, oil
oil and
and
reassemble .
reassemble .
Main
Main valve
valve 26
26 blocked.
blocked.
Disassemble,
Disassemble, clean,
clean, oil
oil and
and
reassemble or replace main valve.
reassemble or replace main valve.
Rotors
Rotors worn
worn or
or blocked.
blocked.
Disassemble,
Disassemble, clean,
clean, oil
oil and
and
reassemble or replace rotors.
reassemble or replace rotors.
Insufficient
Insufficient air
air pressure
pressure
Increase
Increase pressure
pressure in
in receiver.
receiver.
Main
Main air
air pipe
pipe work
work restricted
restricted or
or
insufficient bore.
insufficient bore.
Check
Check all
all pipe
pipe work
work and
and replace
replace
joint it if necessa
joint it if necessary.
ry.
6
6
Pinion engages gear
Pinion engages gear
ring, but will not turn
ring, but will not turn
engine.
engine.
Membrane
Membrane 17
17 broken.
broken.
Replace
Replace it.
it.
Incorrect
Incorrect connection
connection of
of control
control
pipes.
pipes.
Connect
Connect control
control pipes
pipes as
as per
per
installations instructions.
installations instructions.
7
7
Starter starts working
Starter starts working
upon opening the flow
upon opening the flow
valve of the feed line,
valve of the feed line,
although electro valve
although electro valve
are not actuated..
are not actuated..
Main
Main valve
valve 26
26 blocked
blocked and
and open,
open,
valves 8 and 9 blocked or
valves 8 and 9 blocked or broken.
broken.
Disassemble,
Disassemble, clean
clean oil
oil and
and replace
replace
joint if neede
joint if needed.
d.
Main
Main pipe
pipe work
work chocked
chocked or
or its b
its bore
ore
is less than stipulated for the starter.
is less than stipulated for the starter.
Revisar
Revisar toda
toda la
la tubería,
tubería,
cambiándo
cambiándola si
la si su diámetro interior no
su diámetro interior no
es el adecuado.
es el adecuado.
Insufficient
Insufficient air
air pressure.
pressure.
Increase
Increase pressure
pressure in
in receiver.
receiver.
8
8
Lack of starter power..
Lack of starter power..
Badly
Badly worn
worn rotors.
rotors.
Replace.
Replace.
Содержание A-45
