background image

KETS 1141 Titan Illuminated Crossing Telephone 

1.  Safety and Care Information 

 

THIS TELEPHONE IS FOR THE KETS (Kestrel Emergency Telephone 
System) ONLY.  DO NOT ATTEMPT TO CONNECT THIS TELEPHONE TO 
A PABX or PSTN LINE OR TO PETS. 

 

The safety of the user/installer relies on the isolation of the telephone 
network and not on the earthing of the case

 

 

Please read these instructions thoroughly before starting installation.  
These products must be installed by competent personnel familiar with 
telephone installation.

 

 

Telephone network voltages can be hazardous.  Take adequate 
precautions when opening the case or installing.  If in doubt, disconnect 
the telephone line elsewhere before accessing the line connections.

 

 

For increased protection against lightning transients, attach a local 
earth to the main terminal block (see section 7) 

2.  Product Description 

This manual describes the KETS 1141 model Titan telephone, designed for 
use on KETS (Kestrel Emergency Telephone System) at automatic half 
barrier (AHB) level crossings in the UK.  The product was introduced as an 
alternative to PETS, and delivers the functionality of PETS, but is not 
electrically compatible with any PETS interface.  It can only be connected to a 
dedicated KETS interface.  

The product identity label is 

BROWN

 (as opposed to the 

blue

 label visible on 

PETS units) 

 

For the full list of product features, please see the specifications in section 11. 

 

Содержание KETS 1141





















Отзывы: