Gaggenau DF480162CN Скачать руководство пользователя страница 44

Страница: 44 / 52

Fault, what to do?

Appliance interior wet after rinse
cycle.

No appliance fault

On account of the “Condensation drying”
principle, water droplets are physically
induced and required in the container. The
humidity in the air condenses on the inner
walls of the dishwasher, drains and is
pumped out.

Food remnants on the utensils.

Utensils placed too closely together,
utensils basket overfilled.

Arrange utensils with adequate clearance
between them ensuring that the spray jets
can reach the surface of the utensils.
Prevent contact points.

Spray arm rotation obstructed.

Arrange utensils so that the spray arm can
rotate without obstruction.

Spray arm nozzles are blocked.

Clean the spray arm nozzles.

Filters

dirty.

Clean filters.

Filters

inserted incorrectly and/

or not engaged.

Insert and engage filters correctly.

Rinse programme too weak.

Select a more intensive rinse programme.
Increase sensitivity of the sensors.

"Sensor setting" on page 35

Utensils precleaned too intensely;
sensors therefore decide on weak
programme sequence. Stubborn
soiling cannot be completely
removed.

Do not prerinse utensils. Remove only large
food remnants.
Increase sensitivity of the sensors.

"Sensor setting" on page 35

Recommended programme Eco 50° or
Intensive.

Tall narrow receptacles in corner
areas are not rinsed adequately.

Do not place hollow receptacles too
obliquely and do not place in the corner
area.

Top basket

on right and left not

set to same height.

Set top basket to same height using side
levers.

Detergent residue.

Detergent dispenser cover

blocked by utensils and therefore
does not open fully.

Utensils must not be placed above the tablet
collecting tray

. These may block the lid

of the detergent dispenser and prevent it
from opening fully.

"Upper basket"

on page 21
Do not place utensils or fragrance
dispenser in the tablet collecting tray.

Detergent dispenser cover

blocked by the tablet.

Tablet must be inserted flat and not upright.

Tablets used in the quick or short
programme.
Dissolving time of the detergent is
not reached in the selected short
programme.

Dissolving time of tablets too long for a
quick or short programme.
Use a detergent powder or select a more
intensive programme.

Washing effect and dissolving
performance are reduced after a
prolonged storage time or detergent
is very lumpy.

Change detergent.

Water stains on plastic parts.

Droplet formation on plastic surface
is physically unavoidable. After
drying, water stains are visible.

Use a more intensive programme (more
water changes).
Arrange utensils in a sloping position.
Use rinse aid.
If required, increase softening setting.

Fault

Cause

Remedial action

* depending on the configuration of your specific dishwasher

Содержание DF480162CN





















































Результаты поиска

Содержание DF480162CN

Отзывы:

Похожие инструкции для DF480162CN

Бренды по названию

Популярные бренды

Gaggenau DF480162CN, Инструкция по эксплуатации

Результаты поиска

Содержание DF480162CN

Отзывы:

Похожие инструкции для DF480162CN

Бренды по названию

Популярные бренды