background image

REV.11/14 

S/N: 3210 AND ABOVE  

PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS. 

DESCRIPTION 

 

WARNING

The balance of the tool is designed for horizontal use and is not suited for any other application. Gage Bilt will 

be pleased to advise for your specific application. 

 

 
The GB752 is a pneumatic-hydraulic tool designed specifically for the efficient installation of a wide range of blind rivets. It weighs 
4.30 lbs. (1.9 kg) and can be operated in any position with one hand. It has a .500" (12.7 mm) rivet setting stroke and a rated pull load 
of 3800 lbs. (16.9 kN) with 90 psi (6.2 bar) air pressure at the air inlet. 

 

The GB752 riveter is designed to operate on a range of air pressure, with 90 to 100 psi (6.2-6.9 bar) providing the maximum efficiency. 
At 90 psi (6.2 bar) air pressure, the GB752 does not exceed 81.5 dB (A) and consumes 3.9 cfm at 20 cycles a minute. 

 

The air inlet is provided with 1/4-18 female pipe threads to accept the users air hose fitting. 

 

NOSE ASSEMBLIES ARE NOT FURNISHED WITH TOOL AND MUST BE ORDERED SEPARATELY. (See page 12 for nose assembly recommendations.) 

MAINTENANCE 

 

WARNING:

 

Maintenance personnel 

MUST

 

read and understand all warnings and cautions.

 

 

WARNING

Disconnect tool from its power source before performing maintenance.

 

 

WARNING

Excessive contact with hydraulic oil and lubricants should be avoided. 

 

 

WARNING:  

Dispose of Hydraulic Oil in accordance with all environmental regulations applicable in your area. 

 

 

WARNING:  

Read MSDS documents for all applicable materials. 

 

 

The performance of any tool depends upon good maintenance practices. Following these minimal requirements for service and care 
will extend the life of your tool. 
  *Only use an air supply set at 90-100 p.s.i. (6.2-6.9 bar) equipped with a filter-regulator to prevent wear. 
  *The tool will eventually lose some hydraulic oil. Keep the hydraulic system full (only use Dexron III, or equivalent) and free of air by 

using the air bleeder assy (704153) on a weekly basis. 

  *Proper care by operator is necessary in maintaining full productivity and reducing downtime. Read all applicable tool manuals and 

nose assembly data sheets prior to operating tools. 

  

*Keep nose assemblies, especially jaws, clean and free of chips and debris. Lube jaws and collet surfaces that jaws ride on with light 

machine oil on a daily basis. 

*All Screwed End Caps, Base Covers, Air Fittings, Actuators, Screws and Nose Assemblies are to be examined at the end of each 

working shift to check that they are secure. 

*Check tool, all hoses and all couplings daily for damage or air/hydraulic leaks. Tighten or replace (if necessary). 

  *For a complete overhaul, tool kit (GB704TK) is recommended (see page 8). 

TORQUE SPECIFICATIONS

 

Button Head Cap Screws (A-928) = 40 inch lbs. 
Flexlock Nut (400559) = 40 inch lbs.

 

Packing Plug (704118) = 45 foot lbs. 
End Cap (752313) = 45 foot lbs. 
Button Head Cap Screws (402482) = 35-40 inch lbs. 

(Do NOT over

-

tighten)

 

CLEANING AND LUBRICATING PROCEDURE 

 

Daily cleaning and lubrication of nose assembly will greatly reduce downtime 
and increase life of components. Using sewing machine oil, or an equivalent 
cleaner/lubricant, follow instructions below. 
 

1.  Disconnect tool vacuum line (if equipped). 
2.  Point nose assembly into oil as shown (Fig. A). 

 

3.  Cycle tool 8-10 times and wipe dry. 

 

Image may not reflect actual tool 

 

Fig A 

Содержание GB752














Отзывы: