background image

Rev. 9/14 

 

GB7045

 

TORQUE SPECIFICATIONS

 

Button Head Cap Screws (402479) = 40 inch lbs. 
Packing Plug (744118) = 45 foot lbs. 
Flexlock Nut (400559) = 40 inch lbs. 
End Cap (745816) = 45 foot lbs. 
Button Head Cap Screws (402482) = 35-40 inch lbs. 

(Do NOT over-tighten)

 

DESCRIPTION 

 

 

 

 

 

 

 

                 

  Covered under Patent No. 5,485,727 

 

WARNING

The balance of this tool is designed for horizontal use and is not ergonomically best suited for all applications. 

Gage Bilt will be pleased to advise for your specific application. 

 

 

The GB745 is a pneumatic-hydraulic tool designed specifically for the efficient installation of a wide range of blind rivets, lockbolts 
and MAGNA-GRIP® fasteners. It weighs just over 7 lbs. (3.26 kg) and can be operated in any position with one hand. It has  
a .620” (15.75 mm) rivet setting stroke and a rated pull load of 6,300 lbs (28.02 kN) with 90 psi (6.2 bar) air pressure at the air inlet. 
 
The GB745 riveter operates on a wide range of air pressure, with 90 to 100 psi (6.2-6.9 bar) providing the maximum efficiency.  At 90 
psi. (6.2bar) air pressure, the GB745 does not exceed 81.5 dB (A) and consumes 6.0 cfm at 20 cycles per minute. 
  
The air inlet is provided with 1/4-18 female pipe threads for accepting the user's air hose fitting. 
 
Nose Assemblies that were designed for the model 353 installation tool mount directly on the GB745 without the use of an adapter. 
 
Nose Assemblies that were designed for the model 352 installation tool will attach to the GB745 with the use of the 353352 nose 
assembly adapter. 
 
NOSE ASSEMBLIES  ARE  NOT  FURNISHED  WITH  THIS  TOOL  AND MUST BE ORDERED SEPARATELY (SEE PAGE 12). 

 

MAINTENANCE

 

 

WARNING:

 

Maintenance personnel 

MUST

 

read and understand all warnings and cautions.

 

 

WARNING

Disconnect tool from its power source before performing maintenance.

 

 

WARNING

Excessive contact with hydraulic oil and lubricants should be avoided. 

 

 

WARNING:  

Dispose of hydraulic oil in accordance with applicable regulations.

 

 

WARNING:  

Read MSDS documents for all applicable materials. 

 

 

The performance of any tool depends upon good maintenance practices. Following these minimal requirements for service and care 
will extend the life of your tool. 
  *Only use a clean dry air supply set at 90-100 p.s.i. (6.2-6.9 bar) Max. equipped with a filter-regulator to prevent  wear. 
  *Proper care by operator is necessary in maintaining full productivity and reducing downtime. Read all  
  applicable tool manuals and nose assembly data sheets prior to operating tools. 

  

*Keep nose assemblies, especially jaws, clean and free of chips and debris. Lube jaws and collet surfaces that jaws ride on with 

light machine oil on a daily basis. 

*All Screwed End Caps, Base Covers, Air Fittings, Air Actuators, Screws and Nose Assemblies are to be examined at the end of 

each working shift to check that they are secure. 

  *Check tool, all hoses and all couplings daily for damage or air/hydraulic leaks. Tighten or replace (if necessary). 
  *For a complete overhaul, tool kit GB745TK is recommended. 
 

WEEKLY MAINTENANCE 

 

 

Keep the hydraulic system full (only use Dexron III or equivalent) and free of air by using the air bleeder assy (704153) on a 
weekly basis. or as needed. (See Filling and Bleeding). 

 

 

SEE TROUBLESHOOTING AND OVERHAUL FOR FURTHER GUIDANCE. 

 

CLEANING AND LUBRICATING PROCEDURE 

 

Daily cleaning and lubrication of nose assembly will greatly reduce downtime and increase 
life of components. Using sewing machine oil, or an equivalent cleaner/lubricant, follow 
instructions below. 
 
1. Disconnect tool vacuum line (if equipped). 
2. Point nose assembly into oil as shown. 
3. Cycle tool 8-10 times and wipe dry. 

 

Image may not 
reflect actual tool 

Содержание GB745














Отзывы: