Gage Bilt GB744 Скачать руководство пользователя страница 12

Страница: 12 / 13

Rev. 2/15

GB744- SELECTION CHART

DIAMETER

STRAIGHT

RIGHT ANGLE (3)

OFFSET

1/8

456MAX-701-17

1,2

456MAX-753A-54

1,2

456MAX-704-43OS

1,2

5/32

456MAX-744-20

456MAX-744-50OS

3/16

456MAX-749-35

1,2,3

1/4

08MAX-744-20

08MAX-744A-50OS

1) INSTALLS 1/8", 5/32" AND 3/16" DIAMETERS

7/11

3) FRONT END EJECTING NOSE ASSEMBLY.
4) RIGHT ANGLE NOSE ASSEMBLY MAY REQUIRE MORE THAN 1 PULL.

CHERRYM AX® IS A REGISTERED TRADEM ARK OF CHERRY AEROSPACE. HUCKM AX® AND HUCK-CLINCH® ARE REGISTERED TRADEM ARKS OF ALCOA INC.
ALLM AX® IS A REGISTERED TRADEM ARK OF ALLFAST FASTENING SYSTEM S, INC.

FASTENER

CHERRYMAX®

ALLMAX®

HUCKMAX®

HUCK-CLINCH®

MIL-R-7885

NAS9301-9312

BACR15FRFR

BACR15GJ/GK

GAGE BILT CERTIFIES THE GB744 WILL INSTALL THE ABOVE FASTENERS

2) NOSE ASSEMBLIES REQUIRE THE 744704 ADAPTER.

Содержание GB744














Результаты поиска

Содержание GB744

Отзывы:

Похожие инструкции для GB744

Бренды по названию

Популярные бренды

Gage Bilt GB744, Руководство по установке

Результаты поиска

Содержание GB744

Отзывы:

Похожие инструкции для GB744

Бренды по названию

Популярные бренды