background image

REV. 11/14 

 

S/N: 1117 AND ABOVE  

PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS. 

TROUBLESHOOTING 

 

Providing all maintenance conditions have been met, follow this systematic approach to diagnosis. 
 
  1.  MORE THAN ONE PULL IS REQUIRED TO BREAK RIVET. 

a)  Tool needs to be bled. (See filling and bleeding instructions.)  
b)  Spring has fatigued, replace. 
c)  Jaws are stripped or packed with chips. Clean or replace. 
d)  Incorrect nose tip. 
 

  2.  SLOW OR PARTIAL OPERATION WHEN THE ACTUATOR LEVER ASSY (704343) IS DEPRESSED 
  

a)  Polyseal (A-1119) and o’ring (400793) on the piston (713211) could be worn or damaged. Replace. 
b)  Back-up ring (S908) and o’ring (A-201) on the piston rod assy (744136) could be worn or damaged. Replace. 
c)  Muffler (744143) or filter inside valve spool assy (743142) may be plugged with dirt. Clean thoroughly and back-blow with 

compressed air.  

d)  Hole in metering screw in valve spool assy (743142) may be blocked or damaged. Hole diameter should be .028". Clear 

and size or replace. 

 

  3.  NO OPERATION WHEN ACTUATOR LEVER ASSY (704343) IS DEPRESSED 

a)  Tool seized due to mechanical failure or damaged parts. 
 

  4.  OIL LEAKAGE 

a)

  DO NOT

 OPERATE WITH OIL LEAKING FROM TOOL. HIGH PRESSURE OIL MAY CAUSE SEVERE PERSONAL INJURY. 

b)  Any oil leaking externally should be traced to its source.  An o'ring or seal that leaks should be replaced. 
 

  5.  AIR BYPASS FROM VALVE HOUSING 

a)  If the spring (744144) breaks or dislodges, air will flow freely through the muffler (744143). Replace or reset. Valve spring 

installation tool (744151) is recommended. 

b)  Check o'rings on valve sleeve (743144), valve spool assy (743142), and valve plug (744142).  If worn or damaged, replace. 

Valve sleeve removal tool (744152) is recommended. 

 

  6.  FASTENER STEM JAMMED IN NOSE ASSEMBLY 

a)  Nose assembly components require service. 

DISCONNECT AIR FROM TOOL

, remove the nose from the tool and  

 

disassemble. Replace worn or broken parts. Clean the surface the jaws ride on. 

b)  Stems lodged side by side in the follower. Disassemble, remove stems, and reassemble.

 

c)  Incorrect follower.

 

Содержание GB713SH















Отзывы: