background image

3

 

6/11 Rev. 5/22

 

GB704 S/N: 3213 AND ABOVE 

 

PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

 

 

 

Seller warrants that all goods covered by this catalog will conform 

to applicable specifications and will replace or repair, EXW our plant, any 

goods providing defective from faulty workmanship, or material, for 1 year 
from date of shipment

 

 

Said  warranty  to  remain  in  effect  if,  and  only  if,  such  goods  are 

used in accordance with all instructions as to maintenance, operation and 

use, set forth in manuals and instruction sheets furnished by seller.

 

 

Sellers obligation under this warranty shall be limited to the repair 

or rework of the goods supplied or replacement thereof, at Seller

s option, 

and  in  no  case  is  to  exceed  the  invoice  value  of  said  goods.  Under  no 

circumstances  will  the  seller  be  liable  for  incidental  or  consequential 

damages  or  for  damages  incurred  by  the  buyer  or  subsequent  user  in 

repairing  or  replacing  defective  goods  or  if  the  goods  covered  by  this 

warranty are reworked or subjected to any type of additional processing.

 

 

This  warranty  is  void  if  Seller  is  not  notified  in  writing  of  any 

rejections  or  defects  within  1  year  after  the  receipt  of  the  material  by  the 

customer.

 

THIS  WARRANTY  IS  MADE  IN  LIEU  OF  ALL  OTHER  WARRANTIES 

EXPRESSED OR IMPLIED, INCLUDING MERCHANTABILITY.

 

 

WARRANTY

 

  

 

  

 

DECLARATION OF CONFORMITY

 

MANUFACTURER:

 Gage Bilt Inc. 44766 Centre Ct. Clinton Twp. Michigan U.S.A. +1(586

-

226

-

1500)

 

  

WE DECLARE THAT THE EQUIPMENT SPECIFIED HEREIN CONFORMS 

 

TO THE FOLLOWING DIRECTIVES AND STANDARDS 

 

  

Machinery Directive 2006/42/EC

 

 

EN12100

-

1 & EN12100

-

2

 

EN792

-

1:2000+A1

 

  

EU REPRESENTATIVE

Edgar Hausmann GmbH

 

Förster

-

Busch

-

Str. 10

 

D

-

34346 Hann. Münden Germany 

 

 

EQUIPMENT DESCRIPTION: 

GB704 FASTENER INSTALLATION TOOL

 

  

This product specified above conforms to the above dIrectives and standards.

 

  

 

SIGNATURE:

 

  

  

NAME:

 

 BRIAN LEIGH

 

 

 

 

 

 

 

          PRODUCT MANAGER

 

 

 

 

 

 

 

          CLINTON TWP., MI U.S.A.

 

 

 

 

 

 

 

          MAY 2010

 

 

 

 

 

 

 

          +1(586) 226

-

1500

 

GAGE BILT 

Содержание GB704





















Отзывы: