background image

10 

 

Open Window Detection 
 

With open window detection activated, the fan assisted discharge and the balance resistance working will be disconnected 
automatically when a sharp decrease in temperature in the room is detected avoiding energy wastage. After this period of time, 
the storage heater returns to the prior operation mode. 

 

3.7. CURRENT STATUS 

 

In the normal operation of the device, it will be displayed: 
 

-

 

The value of sun set point temperature if the device is operating in sun temperature level in the current time interval. 

-

 

The value of moon set point temperature if the device is operating in moon temperature level in the current time 
interval. 

-

 

The hour (hh:mm) if the device is operating in frost protection temperature level in the current time interval. 

 

By clicking 

 key, the current time settings are shown in the display. (Day in firs time, hour and minute after). 

 

By clicking            or            key, the current temperature level is displayed. (“Sun”, “Moon”, “Frst”). 

 

 

Useful Information 

Pressing simultaneously keys 

and 

will display current temperatures taken from the sensor located in the device and 

another useful data.  

 

By pressing            and           keys, you can navigate among the different information. 
 

-

 

The first data shown in the display is the room temperature taken from the sensor at the bottom of the device. There 

can be a temperature difference between this sensor and a normal thermometer set up in a wall room. This is because 
temperature is different at different heights in the room. The one at the floor is normally lower. User can adjust the 

sensor so that different thermometers show the same temperature. For this you can go to “General Settings” part and 

modify the sensor reading according to P5 setting. 

-

 

By pressing “+” key, the core temperature is shown preceded by the letter “C”. e.g. “C80”

-

 

By pressing “+” key, the air temperature is shown precede by the letter “A”. e.g. “A50”

-

 

By pressing “+” key, the last % of storage heat is shown preceded by “St”. (Only “S” when 100%). e.g. “St80”.

 

-

 

By pressing “+” key, the time that the balance heater has worked in the last on peak rate is shown.

  

 

3.8. GENERAL SETTINGS:

 

HHR general operation settings can be modified. By pressing the

 key at the same time as we turn on the heater with the 

power switch, located at the right-side panel, we gain access to the general settings menu. 
 

Sun 

Temperature value for Sun Temperature level. 

Moon 

Temperature value for Moon Temperature level. 

St   

Initial %  of storage charge. 

P01 

Starting time of reduced (off peak) rate electric period. 

P02 

Ending time of reduced rate electric period. 

P03 

Starting time of the second reduced rate electric period (if not available set up 00.00). 

P04 

Ending time of the second reduced rate period (if not available set up 00.00). 

P05 

Temperature sensor correction (values from -5ºC to +5ºC). 

P06 

Maximum working period of the balance resistance. Set up this value to “0” to cancel the 

balance resistance operation. With balance resistance operation cancelled, the charge 
correction will not operate and the same charging level will be applied every day. 

P07 

Excess of temperature protection during the charge. Degrees higher than the comfort set 
point temperature when the charge is interrupted. (Values 1-2-3-4-5). 

P08 

Degrees Celsius or Fahrenheit (Values: ºC - ºF) 

Open 

Open Window Function Activation. (On / Off) 

 

Advance with the keys

 and

, Push the 

  key to enter in a parameter. Use same keys to modify it.  

 
To save the new values it is necessary to pass through all of them to the last one (P08). 
 

 
 

Содержание ECOHHR20

















Отзывы: