manualshive.com logo in svg

G-WEIKE LC Series, Руководство по эксплуатации, Страница: 3 / 75

Поделиться
Скачать
G-WEIKE LC Series Скачать руководство пользователя страница 3

 

 

2 

 

 

 

Safety Precautions 

Attention 

       

◆

Before  using  the  machine.  users  are  required  to  carefully  read  this  manual  and  other 

operating requirements, strictly abide by the operating specifications. 

Professional are required for operating the machine. 

       

◆

  The machine uses class 4 laser (strong laser radiation ). The laser radiation may possibly 

cause  the  following  accidents: 

①

  emblaze  the  surrounded  flammable  materials; 

②

generate 

other  radiations  and  toxic  or  hazardous  gas  by  processed  objects  during  laser  processing; 

③

direct  irradiation  of  laser  radiation  cause  harm  to  human  body.  Therefore.  fire  fighting  devices 

are required in the operating place of the machine. Stacking flammable or explosive objects near 

the  machine  is  strictly  prohibited.  Good  ventilation  is  a  must.  Only  the  qualified  personnel  are 

authorized to approach the machine. 

       

◆

  The processed  objects and discharged materials are required to satisfy  requirements as 

per local laws and regulations. 

       

◆

  Laser  processing  is  with  potential  risks.  Users  should  carefully  make  sure  if  the 

processed objects are suitable for laser processing. 

       

◆

  There is high voltage and potential risk in the laser machine . Unauthorized disassembly 

by unqualified personnel is prohibited. 

       

◆

  Reliable  earthing  is  required  for  the  machine  and  related  other  equipment  before 

power-on. 

       

◆

  During operating, removing any cover of the equipment is strictly prohibited. 

       

◆

  During operating, the operators are required to observe working status of the machine all 

the time. in case of any abnormality. it is immediately to disconnect power supply and take active 

and corresponding measures. 

       

◆

  After  power-on.  special  personnel  are  required  for  monitoring  Unauthorized  leaving  is 

strictly prohibited 

       

◆

  It is a must to disconnect the power supply before leaving. 

       

◆

  It  is  strictly  prohibited  to  placing  any  unrelated  all-reflective  or  diffusion  reflective 

objects in the machine to prevent laser reflecting to human body or flammable materials. 

       

◆

  The environment for the machine should be dry. free of interference and influences from 

pollution, vibration, high voltage and strong magnet. The operating ambient temperature ranges 

5- 4

0℃

. and the humidity ranges 5-95% (no dew); 

◆

The  machine  should  be  far  from  electric  appliances  sensitive  to  electromagnetic 

interference; 

◆

Operating  voltage:  AC220V.  50Hz.  Power-on  is  strictly  prohibited  in  case  of  unstable 

voltage of the power grid or unspecified voltage. 

Chapter  two  of  this  manual  is  for  Safety  Rules.  Please  refer  to  the  chapter  more  details 

concerning safe operation of the equipment. Users are required to carefully read and abide by all 

the requirements of safety. 

 

Note

：

Note:  User  Should  Comply  With  the  attention  and  Suggestion  in  this  manual;  it 

could bring much easier operation. 

 

 

Содержание LC Series












































































Отзывы:

Нет отзывов