G-Wave BDA-CELLAB/PCSF-33/33-80-OCMG Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 12

background image

Note: Operation of BDA-CELLAB/PCSF-33/33-80-OCMG at maximum gain

with greater than -40 dBm average power incidents on the MOBILE or BASE
ports could cause damage to the BDA.

Gain Attenuation

This Gain Attenuation Access Panel is located inside the BDA enclosure, simply open
the lid and the panel below will be directly visible

.

Note: Applicable for OCMG model only.

PCS UPLINK GAIN

ATTENUATION

CELL DOWNLINK

GAIN

ATTENUATION

CELL UPLINK GAIN

ATTENUATION

PCS DOWNLINK GAIN

ATTENUATION

Page | 11

«
...
9
10
11
12
»

Содержание BDA-CELLAB/PCSF-33/33-80-OCMG













Отзывы:

Нет отзывов

Похожие инструкции для BDA-CELLAB/PCSF-33/33-80-OCMG

Бренд: NAD Страницы: 2

Бренд: NAD Страницы: 2

Бренд: McIntosh Страницы: 36

a-1 C.R.I.S.T.A.L. AUDIOPHILE

Бренд: Definity Audio Страницы: 13

Бренд: Kustom Страницы: 12

Бренд: Rane Страницы: 6

Бренд: Baja Страницы: 20

Бренд: Analog Devices Страницы: 20

Бренд: Positron Страницы: 44

Бренд: NAD Страницы: 59

Subwoofer Gadget

Бренд: Natural Bass Technology Страницы: 2

Бренд: JET CITY AMPLIFICATION Страницы: 12

Бренд: QUAD Страницы: 16

C1000P - SERVICE

Бренд: McIntosh Страницы: 42

Multi-Purpose Amplifier

Бренд: VXI Страницы: 1

Бренд: AMC Страницы: 6

Bass BB BB Preamp

Бренд: XOTIC EFFECTS Страницы: 1

Бренд: Laboga Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды