background image

 

www.g-lites.com 

 

 

 

  Do not operate this device with opened cover!

 

 

 

5

2 Lamp adjustment 

The lamp holder is aligned at the factory. Due to differences between lamps, fine adjustment 

may improve light performance. 

Strike the lamp, open the shutter and the 

iris,  set  the  dimmer  intensity  onto  100% 

and  focus  the  light  on  flat  surface (wall). 

Center the  hot-spot (the brightest part of 

the beam) using the 3 adjustment screws 

“A,  B,  C”.  Turn  one  screw  at  a  time  to 

drag  the  hot-spot,  adjust  the  lamp  until 

the light is even.  

To reduce a hot-spot, pull the lamp in by 

turning  all  three  screws  “A,  B,  C” 

clockwise 1/4-turn at a time until the light 

is evenly distributed. 

 

If the light is brighter around the edge than it is in the center, or if light output is low, the lamp 

is  too  far  back  in  the  reflector.  Push  the  lamp  out  by  turning  the  screws  “A,  B,  C” 

counterclockwise 1/4-turn at a time the light is bright and evenly distributed. 

 

5

3 Rigging   

 

DANGER 

Please consider the respective national norms during the installation! 

The installation must only be carried out by an authorized dealer! 

 
 

The installation of the projector has to be built and constructed in a  way that it can  hold 10 

times the weight for 1 hour without any harming deformation. 

The installation must always be secured with a secondary safety attachment. This secondary 

safety attachment must be constructed in a way that no part of the installation can fall down if 

Содержание 250S





















Отзывы: