FXA JD5385, Инструкция по эксплуатации, Страница: 14 / 92

Before setting the tool down after completing a cut,
be sure that the lower guard has closed and the blade
has come to a complete stop.
ADJUSTMENTS
Caution! Always ensure that the battery is
disconnected from the circular saw before carrying
out any maintenance or adjustments.
DEPTh OF CUT AT 90°
Always keep correct blade depth setting. The correct
blade depth setting for all cuts should not exceed 1/4
in. below the material being cut. More blade depth will
increase the chance of kickback and cause the cut to
be rough. For more depth of cut accuracy, a scale is
located on the upper blade guard.
The Circular Saw has an adjustable depth of cut. To
adjust the depth of cut slacken the lever located on
the side of the machine, Fig.15.
Measure the depth required from the base plate to the
highest point of the blade or use the depth gauge on
the fixed guard, Fig.16.
Tighten the depth adjustment knob securely.
ANGLE OF CUT 0-45°
To adjust the angle of cut between 0-45° slacken the
adjustable angle of cut locking knob, Fig.17.
The base plate assembly will now pivot between 0-
45°. Set the desired cutting angle by using degree
scale at the front of the machine and tighten locking
knobs.
At the front of the base plate there are two notches
marked 0° and 45°. These notches are a guide to
indicate the position of the blade in relation to the cut
being made in the material.
STARTING AND STOPPING
To start the machine, press in the lock-off switch
Fig.18 then depress and hold in the trigger, Fig.19.
There is no need to hold the lock-off switch in as it
remains in place as long as the trigger is depressed.
To stop the saw, release the trigger, which allows the
lock-off switch to return to the locked position. Do not
attempt to jam the lock-off switch.
NOTE: You can depress the lock-off button from either
the left or right side.
Always let the blade reach full speed, then guide the
saw into the workpiece.
MAINTENANCE
WARNING! Always remove battery pack from your
tool when you are assembling parts, making
adjustments, cleaning, or when not in use. Removing
battery pack will prevent accidental starting that could
cause serious personal injury.
WARNING! When servicing only use identical
replacement parts. Use of any other parts may create
a hazard or cause product damage.
WARNING! Always wear safety goggles or safety
glasses with side shields during power tool operation
or when blowing dust. If operation is dusty, also wear
a dust mask.
GENERAL MAINTENANCE
Avoid using solvents when cleaning plastic parts.
Most plastics are susceptible to damage from various
types of commercial solvents and may be damaged
by their use. Use clean cloths to remove dirt, dust, oil,
grease, etc.
Warning! Do not at any time let brake fluids, gasoline,
petroleum based products, penetrating oils, etc.,
come in contact with plastic parts. Chemicals can
damage, weaken or destroy plastic which may result
in serious personal injury.
Electric tools used on fiberglass material, wallboard,
spackling compounds, or plaster are subject to
accelerated wear and possible premature failure
because the fiberglass chips and grindings are highly
abrasive to bearings, brushes, commutators, etc.
Consequently, we do not recommended using this
tool for extended work on these types of materials.
However, if you do work with any of these materials, it
is extremely important to clean the tool using
compressed air.
LUBRICATION
All of the bearings in this tool are lubricated with a
sufficient amount of high grade lubricant for the life of
the unit under normal operating conditions. Therefore,
no further lubrication is required.
TEChNICAL SPECIFICATION
14
Voltage 18V DC
No load speed 3800min -1
Max cut at 90º 54mm
Max cut at 45º 40mm
Blade size ø165 x ø16mm
Sound Pressure Level L
pA
85 dB(A)
K=3dB(A)
Sound Power Level L
WA
96 dB(A)
K=3dB(A)
Vibration Level 5.33 m/s 2 , K=1.5m/s 2