FXA FXAZ1C-HW-3801WEP, Инструкция по эксплуатации

Страница: 9 / 60

9
Use the shortest bit practical.
When drilling deep holes, work in stages, use a short
bit for the beginning of the hole, then change to a
longer bit.
CHISEL OPERATION
Adjust the auxiliary handle as needed.
Set the function by adjusting the mode selector to the
desired setting.
Plug in the power cord.
Squeeze and hold the trigger to turn on the rotary
hammer drill.
Allow the rotary hammer drill to reach full speed
before contacting the work surface.
When finished, to prevent accidents, release the
trigger and disconnect its power supply after use. Pull
back on the chuck then remove the bit from the
chuck. Clean, then store the tool indoors out of
children’s reach.
MAINTENANCE
Warning!
Always switch the product off, disconnect it
from the power supply and let the product cool down
before performing inspection, maintenance and
cleaning work.
Keep the product clean. Remove debris from it after
each use and before storage.
Regular and proper cleaning will help ensure safe use
and prolong the life of the product.
Inspect the product before each use for worn and
damaged parts. Do not operate it if you find broken
and worn parts.
Warning! Only perform repairs and maintenance work
according to these instructions. All further works must
be performed by a qualified specialist.
GENERAL CLEANING
Clean the product with a dry cloth. Use a brush for
areas that are hard to reach.
Remove stubborn dirt with high pressure air (max. 3
bar).
Note: Do not use chemical, alkaline, abrasive or other
aggressive detergents or disinfectants to clean this
product as they might be harmful to its surfaces.
Check for worn or damaged parts. Replace worn parts
as necessary or contact an authorised service centre
for repair before using the product again.
LUBRICATION
Monthly, open the Grease Port, clean out old grease,
and replace with new grease.
Lubricate the bit shank with grease each time before
installing to maintain the life of the internal
mechanism.
Note: Warranty void if grease maintenance (internal
and bit shank) is not followed.
REPAIR
This product does not contain any parts that can be
repaired by the consumer. Contact a qualified
specialist to have it checked and repaired.
STORAGE
Clean the product as described.
Store the product and its accessories in a dry, frost-
free place.
Always store the product in a place that is
inaccessible to children.
The ideal storage temperature is between 10°C and
30°C.
We recommend using the original package for storage
or covering the product with a suitable cloth to protect
it against dust.
TRANSPORTATION
Switch the product off and disconnect it from power
supply before transporting it anywhere.
Attach transportation guards, if applicable.
Always carry the product by its handles.
Protect the product from any heavy impact or strong
vibrations which may occur during transportation in
vehicles.
Secure the product to prevent it from slipping or
falling over.
TECHNICAL SPECIFICATION
Rated voltage 230V~50Hz
Rated power 1050W
No load speed 0-480 min -1
Impact rate 0-3780 min -1
Drilling capacities
Masonry 38mm
Impact energy 10 Joules
Sound Pressure Level L
pA
93.8 dB(A)
Rotary hammer: K=3dB(A)
Chiselling hammer: L
pA
95.8 dB(A)
K=3dB(A)
Sound Power Level L
pA
104.8 dB(A)
Rotary hammer: K=3dB(A)
Chiselling hammer: L
pA
106.8 dB(A)
K=3dB(A)
Vibration Level a
h,Cheq
:14.89 m/s 2 ,
(main handle) K=1.5m/s 2
Vibration Level a
h,Cheq
:13.02 m/s 2 ,
(auxiliary handle) K=1.5m/s 2