9
Slide the battery pack into the tool base, Fig.3. (Note
the battery has raised ribs which allows it to fit into
the pole saw only one way). Make sure the battery
pack snaps into place and that battery pack is
secured in the tool before beginning operation.
Improper installation of the battery pack can cause
damage to internal components.
REMOVING ThE BATTERY PACK
Locate the battery release catch on the top of the
battery and press downwards, Fig.4. Whilst holding
down the battery release catch slide the battery pack
away from the tool.
VARIABLE SPEED CONTROL (FIG. 5)
Simply apply light pressure to the trigger to start the
wrench on a slow speed. Increasing the pressure on
the switch will increase the speed of the wrench.
Note: You might hear a high pitched noise from the
switch during use. Do not be concerned; this is a
normal part of the switch function.
FORWARD & REVERSE SWITCh
This feature is selected via a slide switch located
above the trigger, Fig.6. To select direction of the
wrench rotation simply push the button fully in on the
left side for reverse rotation. To change to forward
rotation push the button fully in on the right side of the
handle.
Note: As a safety precaution from accidental
engagement while being carried pushing the
forward/reverse button into the middle or neutral
position will render the wrench inoperative.
Caution: To prevent gear damage, always allow the
anvil to come to a complete stop before changing the
direction of rotation.
Note: The wrench will not run unless the direction of
rotation selector is pushed fully to the left or right.
Avoid running the wrench at low speeds for extended
periods of time. Running at low speeds under
constant usage may cause the wrench to become
overheated. If this occurs, cool the wrench by running
it without a load and at full speed.
BUILT-IN COUPLER
The tool has a built-in coupler. The coupler has been
designed to accept 1/4 in. hex bits.
INSTALLING BITS
Lock switch trigger on the tool by placing the direction
of rotation selector in center position.
Slide the coupler forward and hold in position.
Insert bit straight into coupler.
Slide the coupler back slowly and release, Fig.7.
REMOVING BITS
Lock switch trigger or the drill by placing the direction
of rotation selector in center position.
Slide the coupler forward and hold in position.
Pull bit straight out of coupler.
WARNING: Make sure the bit is secured in the coupler
before using the impact driver. Failure to do so could
cause serious personal injury.
WARNING: Do not drive a screw where there is likely
to be hidden wiring behind the surface. Contact with a
“live” wire will make exposed metal parts of the tool
“live” and shock the operator. If you must drive a
screw where hidden wire may be present, always hold
tool by insulated gripping surfaces (handle) when
performing the operation to prevent a shock to the
operator.
CAUTION: The impact driver is not designed to be
used as a drill.
INSTALLING ThE BELT CLIP
Before fitting the belt clip set the forward/reverse
button to the centre position or turn tool off and
disconnect battery pack.
To reduce the risk of serious personal injury, do not
suspend tool overhead or suspend objects from the
belt hook. Only hang the tool’s belt clip from a work
belt.
When attaching or replacing the belt clip, use only the
screw that is provided. Be sure to securely tighten the
screw with a Phillips screwdriver.
The belt clip can be be attached to either side of the
tool using only the screw provided, to accommodate
left or right handed users.
To move belt clip, remove the screw that holds the
belt clip in place then reassemble on the opposite
side. Be sure to securely tighten screw.
DRIVING OR REMOVING SCREWS
Place the direction of rotation selector in the correct
position for the operation.
Hold the impact driver with one hand.
Place the bit on the screw head and slowly depress
the switch trigger. Start the bit slowly for more control.
As the screw is driven, impacting will begin.
MAINTENANCE
WARNING! Always remove battery pack from your
tool when you are assembling parts, making
adjustments, cleaning, or when not in use. Removing
battery pack will prevent accidental starting that could
cause serious personal injury.
This power tool normally requires no maintenance;
from time to time the ventilation slots on the motor
casing should be cleaned out. If the unit should
become defective, repair should be performed by an
authorized service agent for electric tools.Avoid using
solvents when cleaning plastic parts.
Содержание FXAJD5083
