FXA 501739306, Инструкция по эксплуатации

Страница: 11 / 42

11
Refer to the ‘Overview’ illustration and to Figs 1 & 2.
Fit the ON/OFF switch to the Motor Stand using the
4 x M4 x 60 mm screws as shown in Fig 1.
Join the Motor Stand and Support Stand together
using the M8 x 80 bolts as shown in Fig 2, using the
spacers between the stand items.
Fit the Connecting Plates to the Motor Stand and
Support Stand, using the M8 x 40 bolts, flat washers
and M8 locknuts.
INSTALLING THE FIXED GUARD
PARTS REQUIRED
Guard Support Bracket: 2 x M8 x 15mm Bolts,
Washers & Locknuts
Fixed Guard: 4 x 8mm washers & locknuts
Attach the Fixed Guard Support Bracket to the motor
mounting plate using 2 x M8 bolts, locknuts &
washers as shown in Fig 3.
Secure the Fixed Guard to the Motor Stand and fixed
Guard Support Bracket with the four flat washers and
locknuts as in Fig 4.
Note: One fixing passes through the support stand.
INSTALLING THE SAW BLADE
PARTS REQUIRED
1 x M20 Bolt
1 x M20 Flat Washer
1 x Saw Blade
Inner/Outer Retaining Discs
Lower Guard
2 x M6 machine screws/washers
Slide the Inner Retaining Disc onto the motor shaft,
followed by the Saw Blade and the Outer Retaining
Disc.
Install the blade in the orientation shown in fig 5,
noting the direction of the arrows on the blade and
ensuring the teeth point in the direction of rotation
shown.
Do not use a blade with no markings, but if they have
become worn away during previous use, inspect the
blade and note the direction of the teeth. Only use
FXA supplied replacement blades.
Never use cracked, blunt or otherwise damaged
blades.
Ensure that the blade used is rated at least equal to
the speed/performance of the machine.
The blade is designed to sit on a machined shoulder
on the drive shaft and must be in this position before
the securing bolt is tightened.
The outer retaining disc has a flat on one side of the
central hole to align with a flat on the motor shaft.
Secure the discs and blade with the flat washer and
M20 bolt.
Use the Locking Wrench to stop the blade from
turning while tightening the nut with the Open Wrench
provided as shown in Fig 6.
Attach the Lower Guard to the fixed guard using the
M6 machine screws and washers as shown in
Figs 7 & 8.
ASSEMBLING THE LOG CRADLE
PARTS REQUIRED
Return Spring Mounting Bracket: 1 x 40mm bolt,
locknut, 2 x washers.
Return Spring Rod: 1 x M6 x 40 bolt, locknut,
2 x 6 mm washers, 1 x R-Clip & 1 x Spring.
Connecting Chain: 2 x M6 x 40mm bolts, 2 M6 nuts
& 4 x washers
Cradle Support Arms: 2 x M8 x 60mm bolts, 2 x M8
locknuts & 2 x washers.
Sliding Guard Plate: 1 x locating bolt.
Bolt the Cradle Support Arms to the Support Frame
using 60mm bolts, nuts & washers, Fig.9.
Taking the weight of the cradle assembly, manouvre
the sliding guard plate to engage with the locating bolt
on the fixed guard.
The sliding guard plate will then support the weight of
the log cradle assembly, Fig.10.
Secure the Connecting Chain between the cradle
support and support stand using the 40mm bolts,
washers & nuts, Fig.11.
Bolt the return spring mounting bracket to the support
arm using the 40mm bolt.
Fit the Return Spring Assembly to the cradle support
arm using a the 40mm bolt, at the same time, feeding
the spring onto the rod before passing the rod
through the return spring mounting bracket. Secure
the spring assembly with the R-Clip, Fig.12.
Lift the cradle and turn the blade gently by hand and
check it is passing cleanly through the gap in the
cradle without touching the sides.
INSTALLING THE HANDLES, PROTECTIVE PLATE
& LOG SUPPORT YOKE
PARTS REQUIRED
Handles:- 4 x M6 x10 hex headed screws.
Protective Plate:-2 x M6 x 6 machine screws
Log Support Yoke
Log Stop Bar