manualshive.com logo in svg

futuredesion LIMIT L41, Руководство пользователя

Поделиться
Скачать
futuredesion LIMIT L41 Скачать руководство пользователя страница 41

If  LOCK is selected for EIFN, terminals 16 & 17 will act as remote lock input. 
Turning the remote lock switch on will keep all the parameter setting from been 
changed. If the switch is opened the lock indicator is extinguished and the 
up/down key is enabled.

Setup

Setup

EIFN = LOCK

EIFN = LOCK

Figure 3-7 
Remote Lock 

Figure 3-7 
Remote Lock 

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

Remote
Lock

EI+

EI

If L_AN (Limit annunciator) is selected for OUT2, the output 2 will act as a Limit 
Annunciator. If the limit is or has been reached and the RESET key (or remote 
reset contacts)has not been pressed since the limit was reached, then the limit 
annunciator output will be energized and the OP2 indicator will be lit and 
remain unchanged until the RESET key or remote reset input is applied.

There are three reference data contained in setup menu. The reference 
data are read only data. The maximum historical PV, displayed by              
,which shows the maximum process value since  the last UNLOCK 
operation. The minimum historical PV, displayed by                , which shows 
the minimum process value since the last UNLOCK operation. The 
abnormal time, displayed by               ,which shows the total accumulated 
time (minutes) during the process has been in abnormal condition since 
the last UNLOCK operation.
The values of reference data will be initiated as soon as the RESET key is 
pressed for 4 seconds (UNLOCK operation). After UNLOCK operation, the 
PV.HI and PV.LO values will start from the current process value and T.ABN 
value will start from zero.

There are three display mode strategies. DISP=SAFE, unit will display the 
word SAFE in the setpoint display whenever L41 is in a Non-Limit condition. 
If a Limit condition occurs, SAFE is replaced by the set limit value .Once 
the limit temperature returns to a Non-Limit condition, SAFE will be 
displayed again. 
Selecting either HSP1 or LSP1 will show the appropriate limit setpoint during 
all operation of the L41. 
Limit process variable is displayed at all times, regardless of DISP selection

Содержание LIMIT L41





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды