manualshive.com logo in svg

futuredesion LIMIT L41, Руководство пользователя

Поделиться
Скачать
futuredesion LIMIT L41 Скачать руководство пользователя страница 15

HIGH/LOW LIMIT OPERATION

HIGH/LOW LIMIT OPERATION

If Hi.Lo is selected for OUT1, the unit will perform high/low limit control. 
When power is applied the OUT1 relay is de-energized. After 6.5 
seconds self-test period, if the process is below the high limit set point 
(HSP1) and above the low limit set point (LSP1), the output 1 relay will 
be energized and OP1 indicator will go off. If the process goes above 
the high limit set point or below the low limit set point, the relay will be 
de-energized, the OP1 indicator will go on and the display will show 
the process value. After the process is within the normal operation 
range, and the RESET key is pressed or the remote reset input is 
applied, the relay will be energized and the OP1 indicator will go off.

LSP1+O1.HY

HSP1

LSP1

HSP1    O1.HY

ON
OFF

OUT1 Relay

A, B, C, D, E, F =Reset is applied
O1.HY= Output1 hysteresis

Figure 1-6 High/Low Limit Operation

Figure 1-6 High/Low Limit Operation

A

B C

D

E F

15

UM L41-Rev 2

Содержание LIMIT L41





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды