FUTABA FP-8SGAP Скачать руководство пользователя страница 4

•FEATURES

The FP-8SGAP was specially developed to use PCM (pulse code modulation) for FAI
RC aerobatics F3A aircraft. It is an extremely noise and dead-point resistant digital
proportional  RC set with a microprocessor in the transmitter and the receiver. Please
read  this manual before using your set.

TRANSMITTER FP-T8SGAP

• RF  module system.  The frequency band can be

changed with one touch.

• DSC  (Direct  Servo  Controller)  allows operation

of the servos without turning on the transmitter.
Wire  operation is possible by using the special
cord supplied  (FSC.1)

•Servo reversing switch for all channels allows

reversing of the servos with the flip of  a switch.

• Dual  rate or non-linear VTR (variable  trace

ratio) aileron, elevator,  and rudder. Two-stage

dual rate on aileron.

• Rudder auto dual  rate.  Rudder dual rate is turn-

ed on and off automatically  with  operation of
the throttle stick.

• 

Newly designed slantable open gimbal sticks

provide maximum operation  feel.  Stick angle
and spring strength can be adjusted.

• Non-slip  adjustable  lever  head. The stick length

can be adjusted by turning the  knob head.

• New  throttle -> pitch control  mixing is perfect

for

variable  pitch propeller which maximizes

engine power and propeller  efficiency.

•Mutual mixing function allows a eleva-

tor, a flaps, and a rudder mixing

and aileron  differential  operation.

• Elevator -> flap mixing is especially advantageous

in circle aerobatics.

• Flap,  spoiler -> elevator mixing allows control of

the aircraft  attitude while using the air brake

(flap, spoiler).

• Throttle  ->  (flap, spoiler) -> elevator mixing al-

lows enhancement of the air braking  effect by

throttle stick operation when diving  and landing.

• Programmable  mixing function permits mixing

with the desired channel.

• Four-function  snap roll switch (timer is option-

al)

• Idle-up lever, the engine idling speed can be

independently  adjusted during throttle -> pitch

control mixing.

• New single-chip  microprocessor allows one-touch

fail safe setting and introduction of an automatic
transmission  system  which eliminates  the need
for fail  safe  setting at the beginning of each

flight and improves safety.

•Pitch control lever. HIGH side pitch of variable

pitch propeller can be adjusted during throttle ->
pitch control  mixing.

• New  ATV  (Adjustable  Travel  Volume) on all

channels  allows  independent adjustment of servo

left, right, up, and down throw.

•Second ATV. Besides  new pushbutton ATV on

aileron and elevator,  conventional  trimmer ATV
is also installed.

• Monitor  lamp comes on when throttle -> flap,

spoiler -> elevator mixing or throttle -> pitch
control  mixing and flap,  spoiler -> elevator mix-

ing and snap roll are set and goes out when they

are in use.

• Fail-safe switch  (function OFF switch) is provid-

ed for each function so that only the desired
functions  need be turned on.

•Throttle ATL (Adjustable  Throttle  Limiter)

makes throttle  linkage simple and positive.

• Two  servo  test functions. A slow sweep to check

neutral characteristic, trackability cycle servo to
test servo operation.

•Tachometer/timer  with  built-in tachometer, up

timer, down timer, integrating timers, and bat-
tery  alarm  functions.

• Built-in  power error  back-up circuit. When the

internal  Nicd battery  approaches the fully  dis-

charged state, an  LED flashes to  indicate that
the memories presetted (memory, ATV, FS,
etc.) are gone. Please  charge battery  and set all
memory functions again.

• Highest  quality extruded aluminum case. So-

phisticated  transmitter  design gives  easy fitness
and comfortable  feeling to your hands.

• Neck strap  supplied as a standard accessory. The

numerous functions of the transmitter can be
easily  performed by supporting the transmitter
from your neck.

Содержание FP-8SGAP







































Отзывы: