FUTABA FP-8SGAP Скачать руководство пользователя страница 30

NOTE:

When  lowering  lever  8 , be careful that the pitch
does not go negative.  This is adjusted during flight.

For example, flight is affected by the temperature,

air pressure, wind, and other conditions. Use this
lever adjusting the speed, pull, etc. to your liking.
Also select the engine tone quality by adjusting

the propeller pitch. Make quiet flights by fine ad-
justing the propeller pitch.

Next, adjust the throttle.  First, set switch  II  to

the OFF position. Adjust the engine idling speed
to 2,200~2,500 rpm with the throttle trim lever

19 .  Then  set  switch II to the ON position and

set the throttle lever to the maximum slow (zero
pitch) position. Adjust  idle up lever 9 for an
engine  speed of 3000 ~ 4000 rpm. Lever 9 is

inoperative  when switch  II  is in the OFF posi-

tion. Use the variable  pitch propeller as an air
brake during dives.

Pitch zero  does not have an air braking  affect. If
the engine is running  at a speed of 3000 ~ 4000
rpm, the air braking  effect will not appear if the
propeller diameter  is too small.
Adjust the throttle so the  pitch is positive and the
engine idles when switch  II  is set to the OFF
position.  Since lever 8 is also operative in this
state, optimum pitch adjustment is possible.

Idle up lever

Operation  when switch

is ON

NOTES:

• The  pitch  always  becomes maximum when the

throttle switch  is set to HIGH.

•The speed cannot be increased with the idle up

lever 9 when the propeller  pitch is zero.

• Since  the air braking effect  is  higher than normal

when landing at zero propeller  pitch, be careful
until you become familiar with the setting.

• Best  result is often  obtained by making the

tuned pipe longer.

Pitch 8-9

Pitch control
high  side trimmer

Pitch 11
(maximum)

VARIABLE PITCH PROPELLER AND ENGINE
POWER MATCHING IS ESSENTIAL FOR MAXIMUM PERFORMANCE

If the throttle stick is operated quickly during

flight, the engine will make an abnormal sound

(sputter). If the engine  sound remains  unnatural,

the pitch control or throttle servo operation tim-

ing can be delayed.

When the throttle  lever is suddenly moved from a

high speed to a low speed, the throttle  operates
before the propeller pitch changes to zero. If the
throttle lever is moved from  HIGH to SLOW, the
pitch will change before the throttle operates.
Set the throttle  delay time with trimmer  [4] and
the pitch delay time with trimmer  [5] . This
provides the same feeling as fixed  propeller aircraft
and allows natural flight.

Fig. 55

Содержание FP-8SGAP







































Отзывы: