background image

 

 

3

 

OVERVIEW

 

 

This Fusion merchandiser is designed for dry heating 

operations throughout the product area. Heat is generated 

from both shelving and deck.  

 

 

• 

Cases should be installed and operated according to 

this operating manual

s instructions to insure proper 

performance.  

 

• 

These Structural Concepts® self

-

service heated 

merchandisers are designed to hold pre

-

heated hot 

foods at 140 °F to 165 °F (60 °C to 74 °C).

 

• 

Product must be pre

-

heated to these temperatures 

PRIOR TO being placed in merchandiser. This case is 

NOT designed to heat product from cold or ambient 

conditions.  

 

• 

This merchandiser is designed for display of 

perishable, packaged products.

 

• 

Improper use will void warranty.

 

 

TYPE 

“1” 

CONDITION

 

 

This unit is designed for the display of products in ambient 

store conditions where temperatures and humidity are 

maintained within a specific range.  

 

COMPLIANCE

 

 

This equipment MUST be installed in compliance with

 

all applicable NEC, federal, state and local 

 

electrical and plumbing codes.

 

WARNING 

 

 

 

Risk of electric shock. Disconnect power before servicing unit.

 

CAUTION!  More than one source of electrical supply is                        

employed with units that have separate circuits.  

 

Disconnect ALL ELECTRICAL SOURCES before servicing.

 

 

WARNING 

ELECTRICAL

 

  HAZARD

 

WARNING 

 

 

Shelves and Decks Are Hot!  Disconnect and allow to cool                    

45 minutes before cleaning or removing from case.

 

 

WARNING 

HOT

 

SURFACE

 

OVERVIEW / TYPE / COMPLIANCE / WARNINGS / PRECAUTIONS / WIRING / PLUGS 

-

  PAGE 1 of 2 

 

• 

Ambient conditions are to be at 55% max. humidity 

and  maximum temperatures of 75 °F (24 °C).  

 

 

INTEGRATED AVERAGE PRODUCT TEMPERATURE

 

 

• 

These units are designed to merchandise product at 

an integrated average product temperature of          

150 °Fahrenheit / 66 °Celsius.

 

 

THERMOMETERS

 

 

• 

Thermometers in equipment reflect internal air 

temperature only (not actual food temperature).

 

• 

Use probe thermometers to determine actual product 

temperatures.

 

 

COMPLIANCE

 

 

• 

Performance issues when in violation of applicable 

NEC, federal, state and local electrical and plumbing 

codes are not covered by warranty.

 

• 

See below compliance guideline.

 

 

WARNINGS

 

 

• 

This page contains important warnings to prevent 

injury or death. Please read carefully!

 

WARNING: This product can expose you to chemicals, including

 

 Urethane (Ethyl Carbamate), which are known to the state of 

 

California to cause cancer and birth defects or other reproductive 

 

harm. For more information go to P65Warnings.ca.gov.

 

Содержание 20-95651





















Отзывы: