manualshive.com logo in svg

Furuno DS-80, Руководство по установке

Поделиться
Скачать
Furuno DS-80 Скачать руководство пользователя страница 25

 

19  

20.  Insert the shaft so the projection on the transducer (1) fits in the groove on the flange (3). 

Move the shaft up and down by hand to confirm that it moves smoothly. 

21.  Tighten the M16 nut (8 pcs.) on the ball valve (20). 

 

22.  Loosely fasten two sets of M8 hex. bolt (13) and M8 spring washer (14) at the top side of 

the lock ring (6). 

23.  Fasten the M8 hex. bolt (13) tightly and the M8 spring washer (14) at the lateral side of the 

lock ring (6) to fasten the shaft (5). 

24.  Fasten tightly two sets of M8 hex. bolt (13) and M8 spring washer (14) fastened at step 22. 

 

25.  Put the fixing plate (21) between the shaft (5) and gland (19). Fasten the plate with two sets 

of M8 hex. bolt (13) and M8 spring washer (14). Check the clearance between the fixing 
plate (21) and the lock ring (6). If the clearance is more than 3 mm, be sure to check that 
the hollow side of the flange (3) is aligned with the projection on the transducer (1). 

 

Содержание DS-80





















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды