manualshive.com logo in svg

Furuno DS-80, Руководство по установке

Поделиться
Скачать
Furuno DS-80 Скачать руководство пользователя страница 19

 

13  

16. Fasten the gland (19) to the top of the shaft (5). 

Gland (19)

Flat washer (8)

Gasket (7)

Flat washer (8)

The projection on the transducer (1)

Flange (4)

Hex. nut (15)(M4x16)
Seal washer (16)(M4)

Apply Three Bond here.
(1104 200G:local supply)

The fore mark on the shaft

Check that they are aligned.

 

17. Apply Kinoruster to both sides of the gasket2 (18), and put it on the gate valve (20). 

18. Put the shaft on the gasket2 (18), and align the hollow side on the spacer (3) with the 

projection of the transducer (1). 

19. Remove M8 hex. bolt (13) and M8 spring washer (14) from the lock ring to free the shaft (5). 

20. Use the M16 hex. bolt (12), M16 nut (10) and M16 spring washer (11) to fasten the       

flange (4) loosely. 

21. Insert the shaft so the projection on the transducer fits in the groove on the spacer (3). Move 

the shaft up and down by hand to confirm that it moves smoothly. 

22. Tighten the M16 nut(8 pcs.) on the gate valve (20). 

Hex. bolt (13)(M8x30)
Spring washer (14)(M8)

Lock ring (6)

Flange (4)

Shaft (5)

Transducer (1)

Hex. bolt (12)(M16x60)

Gasket2 (18)
(Apply Kinoruster to both sides.)

Nut (10) (M16)
Spring washer (11)(M16)

Gate valve (20)

Spacer (3)

Align the hollow side of
the spacer (3) with the projection
on the transducer (1).

Transducer (1)

Spacer (3)

View from "A"

Hex. bolt (13)(M8x30)
Spring washer (14)(M8)

 

Содержание DS-80





















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды