manualshive.com logo in svg

Funkwerk P/N 800ATC-A-(201)-(301), Эксплуатация и установка

Поделиться
Скачать
Funkwerk P/N 800ATC-A-(201)-(301) Скачать руководство пользователя страница 31

TRT800A / P/N 800ATC-A-(201)-(301)  

Operation and Installation 

 

 
 

31

Document-No: 03.2112.010.71e / Revision: 1.02

4.2 Configuration 

 

Programming of the ICAOA 24-bit Aircraft Address and of 
the Aircraft Category shall be executed by 

qualified 

personnel

 only! 

A wrong Aircraft Address or Flight ID may cause serious 
problems ATC or with ACAS/TCAS systems! 

Pilot and owner

are responsible for correctly set 

transponder data. 

 

4.2.1 Setup 

Steps 

Initially after installation 
The entered ICAO 24-bit address is stored in one out of eight possible 
records (Record=Presetting). Beside the 24bit address and the FID one 
record stores also the settings made for the serial interface (GPS/COMM 
A/B) and also for the optionally installed Ground-Switch. A stringently 
required input is the speed category (RI) of the respective aircraft (see 
section 4.1.6 “Reply Information - Speed Category (RI)“). 

All those data are stored in one record. If more than one record exists, a 
record can be selected out of a list during start-up of the transponder. 

Step 

Display (Example) 

1. Start-up 

Transponder 

 

2.  Ensure, the transponder-mode is 

„STBY“. If necessary change the 
mode by pressing 

 

 

 

Any menu item can be passed by 

. If no changes are 

made the original settings will remain stored. Modification of 
one menu item does not impact the others. No entries will be 
deleted. 

Содержание P/N 800ATC-A-(201)-(301)









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды